Go Back   Home > Forums > Commercial Sector > Group Buys

Group Buys Members group buys

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 1st September 2010, 05:49 AM   #41
diyAudio Member
 
Tarasque's Avatar
 
Join Date: Dec 2002
Location: Netherlands
Hi Sakis,

I still have 4 boards reserved for you. Do you still need them?
  Reply With Quote
Old 1st September 2010, 06:04 AM   #42
diyAudio Member
 
Tarasque's Avatar
 
Join Date: Dec 2002
Location: Netherlands
Quote:
Originally Posted by AndrewT View Post
for every "circuit" that has a flow and return route then the pair of flow and return must have a low loop area to minimise pick up of interference from other noisy sources and to minimise the radiation of interference from this circuit.

Where the flow and return involve three wires (as in a dual polarity supply to an amplifier), all three wires must be formed into a triplet with low loop area.

Twisted is the easiest way to achieve low loop area and low interference with wiring.
Parallel close space traces on a PCB achieve similar.
Hi Andrew...I typically braid the power wires to the power stage. In my latest designs of cases I managed to keep the wires from the power caps to the power stage below 7cm.

I also made a pass X350 and used an L shaped aluminium bracket of 150 x 100 mm and 10mm thick to couple the power stage to the heatsink. . On top I mounted the power stage and on the other side the power cap PCB. I ran the wires through the bracket and kept the wires under 3cm. At the same time I had the speaker terminals close by as well. The L-shaped bracket is also used as groundplane as the 2 L shapes are interconnected at the star ground.
When driving loads under 2 ohms, this arrangement is key...especially when currents of over 20A were observed.
  Reply With Quote
Old 26th May 2011, 06:59 AM   #43
sunil is offline sunil  India
diyAudio Member
 
Join Date: May 2003
Location: Bangalore, INDIA
Default Boards availability

Hi,

If it is possible to get boards for this project I would be interested. Please pm or send me a message. Thanks.
  Reply With Quote
Old 6th June 2011, 07:55 PM   #44
diyAudio Member
 
Join Date: Nov 2009
Hi,
what is the diffrence between version 3.0 & 3.01 ??? can anybody tell???

Thanks
  Reply With Quote
Old 15th February 2012, 04:39 AM   #45
sunil is offline sunil  India
diyAudio Member
 
Join Date: May 2003
Location: Bangalore, INDIA
Default Boards for sale

Hi,

I have a pair of these boards (Lynx ver 3.01) for sale.

I'm selling because I 've bitten more than I can chew. I was building a P3A (Rod Elliott) and didn't realize how much power this really is - 150/275/450 @ 8/4/2 ohms
I'm very happy with the P3A. The cost of the heat-sinks, case, transformer here in India may net be worth the trouble, not to add the difficulty of getting the 16 transistors required.

I paid 17Euro each (42 for the pair with shipping) and have a stereo pair for sale.


Please see links for additional info.

Official LYNX Power Amp builder’s thread
  Reply With Quote
Old 18th February 2012, 08:39 AM   #46
sunil is offline sunil  India
diyAudio Member
 
Join Date: May 2003
Location: Bangalore, INDIA
Default Lynx 3.01 boards

Ping....no takers ?
  Reply With Quote
Old 18th February 2012, 10:28 AM   #47
diyAudio Member
 
Join Date: Mar 2004
Location: Texas
I clicked on Jan's link to the assembly guide but got the 404 error.

I'm interested in this amp if all the components are available.
__________________
Any technology sufficiently advanced is indistinguishable from magic
  Reply With Quote
Old 18th February 2012, 12:50 PM   #48
sunil is offline sunil  India
diyAudio Member
 
Join Date: May 2003
Location: Bangalore, INDIA
Default Lynx 3.01 boards

Hi,

Are you after the boards or just the doco. I've attached the doco if it is useful.

Regards,
Sunil
  Reply With Quote
Old 18th February 2012, 01:14 PM   #49
diyAudio Member
 
Join Date: Mar 2004
Location: Texas
If the documentation is available then I'm interested in the boards.
__________________
Any technology sufficiently advanced is indistinguishable from magic
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Power Amp PSU Board (for e.g. LYNX Amp) Jan Dupont Group Buys 462 4th September 2009 12:31 PM
DELTA PA-34A Power Amplifier by Jan Dupont MEGA_amp Solid State 8 21st January 2005 06:30 PM
LYNX amp problems...Help JojoD818 Solid State 209 18th November 2003 01:10 PM


New To Site? Need Help?

All times are GMT. The time now is 06:45 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright ©1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2