TB W3-871s => Buschhorn mkII

rho · 27th May 2005, 08:05 PM

Short question: Has anyone tried the TB W3-871s in the Buschhorn mkII?

weidok · 28th May 2005, 10:04 AM

Quote:

Originally posted by rho
Short question: Has anyone tried the TB W3-871s in the Buschhorn mkII?

Short answer: i do not know..

here is another TB in a Buschhorn

http://www.speaker-online.de/buschhorn/BHmk2TB.html

rho · 28th May 2005, 10:43 AM

Hey weidok,

I already knew that one. There is a version for 3"drivers too. It's that one I'll be bulding.
I was planning on starting the project today, but something came between it. I'll have to wait until next saturday.

I'm just looking for tips and tricks to get the maximum out of the TB's in this horn-desing.

Scottmoose · 28th May 2005, 11:06 AM

I think you might need to use a little more than the normal amount of stuffing to take the mids down slightly, as I believe the TB has a reputation for being a little hot. Either that or perhaps some contour filtering; I doubt you'd need to alter the basic design much. What are you intending to build them out of BTW?
Scott

rho · 28th May 2005, 11:22 AM

For the the first attempt I'll be using MDF.

Where do I need to put the extra stuffing: Directly behind the driver or in the vertical part near the mouth?

Can I use the RLC network, also used in the Lancetta , to "tame" the TB?

27th May 2005, 08:05 PM	#1
rho diyAudio Member Join Date: Sep 2003 Location: Peer, Belgium	TB W3-871s => Buschhorn mkII Short question: Has anyone tried the TB W3-871s in the Buschhorn mkII?

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Buschhorn MkII w/ Foster W422, aka Fostex FE103A	DRCope	Full Range	54	11th April 2013 04:03 AM
Buschhorn MkII TB	Mayday	Full Range	0	31st March 2007 05:59 PM
Building Buschhorn MKII for 12 CM driver	Harderror	Full Range	23	16th April 2006 03:33 AM
Buschhorn mkII	Fuling	Multi-Way	26	31st August 2004 07:39 PM

New To Site?	Need Help?
Register to Participate Search Privacy Statement Contact Us	Frequently Asked Questions Did you forget your password? Mark Forums Read


	Please consider donating to help us continue to serve you. Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving

28th May 2005, 10:43 AM	#3
rho diyAudio Member Join Date: Sep 2003 Location: Peer, Belgium	Hey weidok, I already knew that one. There is a version for 3"drivers too. It's that one I'll be bulding. I was planning on starting the project today, but something came between it. I'll have to wait until next saturday. I'm just looking for tips and tricks to get the maximum out of the TB's in this horn-desing.

28th May 2005, 11:06 AM	#4
Scottmoose diyAudio Member Join Date: Mar 2005 Location: UK	I think you might need to use a little more than the normal amount of stuffing to take the mids down slightly, as I believe the TB has a reputation for being a little hot. Either that or perhaps some contour filtering; I doubt you'd need to alter the basic design much. What are you intending to build them out of BTW? Scott

28th May 2005, 11:22 AM	#5
rho diyAudio Member Join Date: Sep 2003 Location: Peer, Belgium	For the the first attempt I'll be using MDF. Where do I need to put the extra stuffing: Directly behind the driver or in the vertical part near the mouth? Can I use the RLC network, also used in the Lancetta , to "tame" the TB?