Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

sub amp question for MJK open baffle
sub amp question for MJK open baffle
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 12th May 2009, 02:23 AM   #1
pforeman is offline pforeman  United States
diyAudio Member
 
Join Date: Aug 2008
Default sub amp question for MJK open baffle

I am building the Hframes now for the 18" goldwood (wow is it big!). I plan on using a plate amplifier from Parts Express to power it along with a simple se amp from tubelab for the full range driver.
I will be using one plate amplifier per speaker (one for R , one for L)
My question is: if I use one interconnect to each plate amp, am I utilizing only half of its amplifer section? Should I use a Y connector on the interconnect to get my pre amp to drive both sections of the plate amp, or will I drive both sections of the plate amp by just connecting it to one (R) or (L) of the plate amp

Thanks,
paul
  Reply With Quote
Old 12th May 2009, 02:42 AM   #2
JAG Audio is offline JAG Audio  United States
diyAudio Member
 
Join Date: Nov 2007
What model plate amp?
  Reply With Quote
Old 12th May 2009, 02:02 PM   #3
Cal Weldon is offline Cal Weldon  Canada
Speakerholic
diyAudio Moderator
 
Cal Weldon's Avatar
 
Join Date: Jan 2004
Location: Near Vancouver
sub amp question for MJK open baffle
Some amps will bridge if you use the R only but why not just get Y connectors?
__________________
planet10 needs your help:
Let's help Ruth and Dave
  Reply With Quote
Old 12th May 2009, 02:17 PM   #4
pforeman is offline pforeman  United States
diyAudio Member
 
Join Date: Aug 2008
I thought it would look nicer without the Y connector.
It is the 100 W Dayton audio model
I thought as I'm using two of them 100 watts would be enough.
Also, my SET amp will only put out about 8 watts, albeit on significantly higher sensitivity full range drivers.
Paul
  Reply With Quote
Old 12th May 2009, 02:51 PM   #5
Cal Weldon is offline Cal Weldon  Canada
Speakerholic
diyAudio Moderator
 
Cal Weldon's Avatar
 
Join Date: Jan 2004
Location: Near Vancouver
sub amp question for MJK open baffle
That amp like most sums the signal to a mono so whether you run one channel in or divide it into two before it sums them shouldn't matter. Me, I like the symmetry of seeing both inputs filled so I would use a Y just because it looks better, not worse.
__________________
planet10 needs your help:
Let's help Ruth and Dave
  Reply With Quote
Old 12th May 2009, 07:53 PM   #6
j.michael droke is offline j.michael droke  United States
diyAudio Member
 
Join Date: Jan 2009
Default U frame, power question

Hi there Cal: I am constructing a U frame with a 15-inch driver, closley matching a Martin King example (24-inches long, area = 1.3xSd, Qts=.927), and since Martin King has impounded the Mathcadd work sheets, I'm without information on the power needed. I have a 100watts per channel amplifier available and hope to reach 98db at 27Hz (low note on the piano), which will also cover the orchestrial bass instruments at 31hz (Bb). I plan on crossing over at 70hz. Is this a safe and plasuable plan?

T/S parameters supplied with the sub for 8 ohms: Fs=25hz, Qts=0.927, Qms=6.498, Qes=1.081, Vas=6.81cf, Xmax=6.3mm, Le=7.2, Le=2.56, SPL=95db (probabily at 1000Hz), Bl=15.22, 700wrms, Vc is a DVC connected in series for 8 ohms imp.
....regards, Michael
  Reply With Quote
Old 12th May 2009, 08:18 PM   #7
Cal Weldon is offline Cal Weldon  Canada
Speakerholic
diyAudio Moderator
 
Cal Weldon's Avatar
 
Join Date: Jan 2004
Location: Near Vancouver
sub amp question for MJK open baffle
Hello Michael,

Not wishing to rain on anyone's parade but I'm not sure you're headed in the right direction with that combo. I am thinking it's a small motor driver, not really a subwoofer and to expect 27Hz from it is asking a lot.

Also, this is hijacking pforeman's thread so may I suggest you start a new thread and we can deal with it there?

Thanks.
__________________
planet10 needs your help:
Let's help Ruth and Dave
  Reply With Quote
Old 15th May 2009, 07:19 PM   #8
brookbh is offline brookbh  United States
diyAudio Member
 
Join Date: Jan 2008
Could you get some pics on how you wire up the h-frames?
  Reply With Quote

Reply


sub amp question for MJK open baffleHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
A MTMvTMM? & A Open Baffle Question Ben Reginato Multi-Way 1 18th October 2006 12:06 PM
Open Baffle vs Box Speaker Question Robert McLean Full Range 23 24th May 2005 09:54 PM
Soundeasy Open Baffle Question DougL Multi-Way 2 20th April 2005 12:38 PM
Cheapo open baffle XO/EQ question amt Parts 0 5th April 2004 11:29 PM
Electrostatic HF, Open Baffle LF Question mrfeedback Multi-Way 1 21st August 2002 02:40 AM


New To Site? Need Help?

All times are GMT. The time now is 11:23 AM.


Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 16.67%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright ©1999-2017 diyAudio
Wiki