will Bruce work with my Pana 8 TS?

freddi · 26th July 2007, 10:02 PM

I once eyeball simmed Bruce with AJ - but not sure of Bruce chamber, throat, path and flare - any quick guestimates?

is qts below too high for Bruce? - don't like much peaking near cutoff, stright pipe MLTW wouild work, fat BIB would probably work

my 1st WT2 measurements (later set pretty much the same)

Unit #1

Revc = 5.4657 ohms
Fms = 58.1931 Hz
Zmax = 52.8627 ohms
Qes = 0.5830
Qms = 5.0553
Qts = 0.5227
Le = 0.2559 mH (at 1 kHz)
Diam = 161.9504 mm ( 6.3760 in )
Sd =20599.3690 mm^2( 31.9291 in^2)
Vas = 33.9940 L ( 1.2005 ft^3)
BL = 6.7431 N/A
Mms = 13.2638 g
Cms = 563.9369 uM/N
Kms = 1773.2482 N/M
Rms = 0.9593 R mechanical
Efficiency = 1.0798 %
Sensitivity= 92.3513 dB @1W/1m
Sensitivity= 94.0057 dB @2.83Vrms/1m

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
WTB: Pana FC small caps	cartman	Swap Meet	0	15th November 2008 01:16 PM
Could anyone lend me his/her ESR/ESL meter for measuring Pana FC/FM/TSUP caps?	antomas	Parts	1	4th January 2007 05:29 PM
WTB-WTT Pana FC 220uF 50 or 63V	Andypairo	Swap Meet	0	2nd October 2006 07:18 PM
Cerafine vs. Muse vs. Pana FC?	Sanaka	Parts	12	9th November 2004 10:45 AM
Elna Silmic vs. Pana FC for digital supplies?	dorkus	Parts	0	7th December 2002 09:23 PM

New To Site?	Need Help?
Register to Participate Search Privacy Statement Contact Us	Frequently Asked Questions Did you forget your password? Mark Forums Read


	Please consider donating to help us continue to serve you. Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving

26th July 2007, 10:02 PM	#1
freddi diyAudio Member Join Date: Aug 2005	will Bruce work with my Pana 8 TS? I once eyeball simmed Bruce with AJ - but not sure of Bruce chamber, throat, path and flare - any quick guestimates? is qts below too high for Bruce? - don't like much peaking near cutoff, stright pipe MLTW wouild work, fat BIB would probably work my 1st WT2 measurements (later set pretty much the same) Unit #1 Revc = 5.4657 ohms Fms = 58.1931 Hz Zmax = 52.8627 ohms Qes = 0.5830 Qms = 5.0553 Qts = 0.5227 Le = 0.2559 mH (at 1 kHz) Diam = 161.9504 mm ( 6.3760 in ) Sd =20599.3690 mm^2( 31.9291 in^2) Vas = 33.9940 L ( 1.2005 ft^3) BL = 6.7431 N/A Mms = 13.2638 g Cms = 563.9369 uM/N Kms = 1773.2482 N/M Rms = 0.9593 R mechanical Efficiency = 1.0798 % Sensitivity= 92.3513 dB @1W/1m Sensitivity= 94.0057 dB @2.83Vrms/1m

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)