PetruV's corner of the forum

PetruV · 24th February 2013, 02:35 PM

Here i will cry for all my help, so i wont need to open a new thread.
All my questions will be posted here,mostly elecronics but you may also see something else from time to time!
So pile on!Also ask your own queastions here so me and the others can answer them!
I had a post like this before but it lost popularity since it wasnt properly named so here i go again,and as i said i wont open any other threads appart from this one
Go to the latest pages to see my latest problems and answers

PetruV · 24th February 2013, 02:38 PM

Ok right now im searching for a high power amp circuit which is rather simple and over 500w
I thought the apex b500 would do it but i also want to see some other possibilties

dannyjmf · 24th February 2013, 02:45 PM

ok .... TDA2003s were budget and low cost ... i build it before already ... but power were just too low and it was replaced by the 4channel LM1875 as i shown ... Other options were TDA2005H and also TDA2009A which also i build before and sounds great ...

PetruV · 24th February 2013, 03:35 PM

Quote:

Originally Posted by dannyjmf

ok .... TDA2003s were budget and low cost ... i build it before already ... but power were just too low and it was replaced by the 4channel LM1875 as i shown ... Other options were TDA2005H and also TDA2009A which also i build before and sounds great ...

I have a 2003 kit and it sounds awesome but 1 out of 2 just outputs a very faint quiet and distorted sound and i dont know why ,

PetruV · 24th February 2013, 05:41 PM

Acualy some diferent tda2003 have this problem not the one on the kit sorry for messing up my words

PetruV · 08:03 PM

im making my plans to build a apex d200.2 with irfb4229 at 90v for a good amount off bass'with smps and 2 chanels integrated in a box not bigger than a cable box decoder

PetruV · 17th March 2013, 04:50 PM

Can you help me with and switch mode power supply circuit that is simple and outputs +/- 90v and simple to build and also includes pcb layout.
Please help me since this is very important

PetruV · 26th March 2013, 07:57 AM

I now need a schematic with pcb for a 50w amp

PetruV · 30th March 2013, 09:57 AM

Fixing an amp that integrates 2x tda2030 and one lm1875t,i was a no brainer that its problem was caused by a bad contact,but its been like that for years only using one channel,its time t fix it,and remove the high pass filters from the sattelites and remove the 4x 1 ohm resistors beetwen the sattelites and the amps output.
Any other tweaks you recommend,im very happy to fix this

sakis · 30th March 2013, 10:28 AM

do you take advice ??? I f you do here is one ...

Trust me on this if you cannot understand why the TDA thing had a lot of distortion , if you listen to people that suggest TDA circuits for power over 500W then your available option is like that :

1) The chances that you successfully built an Apex 500 are very very very very very very very very very very LOW !
2) The chances that you successfully built an Apex 500 with a smps power supply are very very very very very very very very very very LOW ! and more
dangerous
3) expect the popularity of your thread to go even worst than the previous ...

24th February 2013, 02:35 PM	#1
PetruV diyAudio Member Join Date: Dec 2012 Location: Bucuresti	PetruV's corner of the forum Here i will cry for all my help, so i wont need to open a new thread. All my questions will be posted here,mostly elecronics but you may also see something else from time to time! So pile on!Also ask your own queastions here so me and the others can answer them! I had a post like this before but it lost popularity since it wasnt properly named so here i go again,and as i said i wont open any other threads appart from this one Go to the latest pages to see my latest problems and answers

6th March 2013, 08:01 PM	#6
PetruV diyAudio Member Join Date: Dec 2012 Location: Bucuresti	im making my plans to build a apex d200.2 with irfb4229 at 90v for a good amount off bass'with smps and 2 chanels integrated in a box not bigger than a cable box decoder Last edited by PetruV; 6th March 2013 at 08:03 PM.

17th March 2013, 04:50 PM	#7
PetruV diyAudio Member Join Date: Dec 2012 Location: Bucuresti	Can you help me with and switch mode power supply circuit that is simple and outputs +/- 90v and simple to build and also includes pcb layout. Please help me since this is very important __________________ I may ask a lot of questions,i may seem very impacient to get an answer,but thats my way of being

26th March 2013, 07:57 AM	#8
PetruV diyAudio Member Join Date: Dec 2012 Location: Bucuresti	I now need a schematic with pcb for a 50w amp __________________ I may ask a lot of questions,i may seem very impacient to get an answer,but thats my way of being

30th March 2013, 10:28 AM	#10
sakis diyAudio Member Join Date: Jan 2006 Location: nea makri athens greece	do you take advice ??? I f you do here is one ... Trust me on this if you cannot understand why the TDA thing had a lot of distortion , if you listen to people that suggest TDA circuits for power over 500W then your available option is like that : 1) The chances that you successfully built an Apex 500 are very very very very very very very very very very LOW ! 2) The chances that you successfully built an Apex 500 with a smps power supply are very very very very very very very very very very LOW ! and more dangerous 3) expect the popularity of your thread to go even worst than the previous ... __________________ SERVICE ΕΝΙΣΧΥΤΩΝ ΚΑΙ ΙΑΠΩΝΙΚΩΝ ΜΗΧΑΝΗΜΑΤΩΝ ΗΧΟΥ www.eastelectronics.gr


	Please consider donating to help us continue to serve you. Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving

24th February 2013, 02:38 PM	#2
PetruV diyAudio Member Join Date: Dec 2012 Location: Bucuresti	Ok right now im searching for a high power amp circuit which is rather simple and over 500w I thought the apex b500 would do it but i also want to see some other possibilties

24th February 2013, 02:45 PM	#3
dannyjmf diyAudio Member Join Date: Feb 2010 Location: Malaysia - Melaka	ok .... TDA2003s were budget and low cost ... i build it before already ... but power were just too low and it was replaced by the 4channel LM1875 as i shown ... Other options were TDA2005H and also TDA2009A which also i build before and sounds great ...

24th February 2013, 05:41 PM	#5
PetruV diyAudio Member Join Date: Dec 2012 Location: Bucuresti	Acualy some diferent tda2003 have this problem not the one on the kit sorry for messing up my words

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
What happens when a sub is in a corner	djn	Subwoofers	26	19th May 2011 08:04 PM
Forum 'Category' appears at the top of the forum list	dfidler	Forum Problems	0	14th August 2010 07:55 PM
Forum donation in honour of a forum member	tinitus	Everything Else	0	25th October 2009 01:45 PM
French people on the forum ? Des Français sur le forum ?	frankie	Introductions	19	30th December 2002 08:40 PM
out of the corner....	ChesterFuzzin'	Multi-Way	6	6th June 2002 09:13 PM

New To Site?	Need Help?
Register to Participate Search Privacy Statement Contact Us	Frequently Asked Questions Did you forget your password? Mark Forums Read