NEwbie question about Routers - diyAudio
Go Back   Home > Forums > General Interest > Everything Else

Everything Else Anything related to audio / video / electronics etc) BUT remember- we have many new forums where your thread may now fit! .... Parts, Equipment & Tools, Construction Tips, Software Tools......

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 19th January 2003, 06:11 AM   #1
diyAudio Member
 
Join Date: Dec 2001
Location: Earth
Default NEwbie question about Routers

I just bought a DEwalt router with no router bits.
I plan on doing speaker cabinets in the future and also making 45degrees connection of the wood like mitre but using a router
what bits should i get ? much help needed.
if anyone is that free do help in writing the various bits and it's uses
thanks for the help
  Reply With Quote
Old 19th January 2003, 09:21 AM   #2
zeno is offline zeno  Europe
diyAudio Member
 
Join Date: Aug 2002
Location: Belgium
I am planning on buying a router too, because I am going to build new speakers.

If anyone has useful tricks on using a router, they are most welcome!

Marc
  Reply With Quote
Old 20th January 2003, 05:27 PM   #3
diyAudio Member
 
Join Date: Dec 2002
Location: CA
Check out the following site:

http://www.grizzly.com

Look under router bits and you can see pictures of all dfferent
kinds. Personally I don't use a mitered corner because I always
cut a ledge and inlay hardwood trim, so a butt joint is easiest,
strong and accurate.

The bit you may want is called a Locking Miter.
Much better than a straight 45 degree edge.
  Reply With Quote
Old 20th January 2003, 05:44 PM   #4
diyAudio Member
 
Join Date: Oct 2002
Location: pittsboro, NC
I would invest in a set of hearing protectors and safety gogles!
for straight cuts I like to clamp a straight edge onto the wood.
For deep cuts, do them in a series of shollow cuts - saves bits.
and the old addage:
measure twice, cut once.
  Reply With Quote
Old 20th January 2003, 09:40 PM   #5
zeno is offline zeno  Europe
diyAudio Member
 
Join Date: Aug 2002
Location: Belgium
I guess a wise man practises first...

At least that's what I will do!

Marc
  Reply With Quote
Old 21st January 2003, 02:08 PM   #6
Schaef is offline Schaef  United States
diyAudio Member
 
Join Date: Jan 2001
Location: Cuyahoga Falls, OH
Default Suggestions from a woodworker

Okay, here are some suggestions from a woodworker who lurks in audio areas. The first couple of bits I would look at buying if I were you, would be a straight cutting bit. (spiral bit, with up-spiral) This bit will be used to plunge into the wood and cut the holes for the drivers. Second, a rabbetting bit or two. This is a bit that looks similar to a straight cutting bit, with the exception that it has a bearing on the bottom, and the cutter is wider than the bearing. This is used to cut the rabbet in the driver hole so you can flush mount the driver.

I would recommend staying away from doing mitered corners, they're not as strong as butt joints, and they're a pain to get completely flush. The lock mitre bit that was suggested, while a very good idea, requires a router table. (Or at least I wouldn't attempt it any other way) If you're concerned about how the joints are going to look, then look at using dovetail joints or box joints. (Don't attempt these on MDF, you'll go mad trying to get it right, only attempt on solid wood or plywood)

I also second the recommendation on hearing protection minimum. (routers are very loud, and you'll be spending time close to it) Eye protection is a definate plus as well. (I wear glasses, so don't think about it as much, even though I should)

As for good sources for the bits, grizzley is good. (Given above) You can also look at Rockler Woodworking or RouterBits.com and finally you could try Whiteside Router bits .

Hope this helps you out!
  Reply With Quote
Old 22nd January 2003, 01:14 AM   #7
Tim F is offline Tim F  England
diyAudio Member
 
Join Date: Jan 2003
Location: Buxton England
Default Router Bits

I'm a newbie to the forum too but not too routing
Where possible buy Tungsten Carbide Tipped bits (TCT) as the resins in Chipboard & MDF blunt normal high speed steel bits very quickly. If the bit is blunt, not only will it not cut cleanly but will overheat rendering it permanent scrap.
A good book to get hold of is 'Advanced Routing Techniques' by Patrick Spielman. Dont be put off by the 'advanced' it,s easy to follow has plenty of basic advice as well as a multitude of jigs to make jobs easier & finishes with a section on building your own router table.
Hope this helps. Most versatile tool i've ever bought.

SAFETY:- A piece of cutter breaking off during cutting from a 1"diameter router bit turning at 18,000 RPM leaves the bit at 4,712 feet/minute or 78.54 feet/second if you prefer (If you cant run this fast wear a good head shield.

P.S. I use CMT router bits if you can get them. (Not the cheapest & not the dearest, but i've never replaced one.
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Forum options for routers zigzagflux Everything Else 3 16th June 2009 01:57 PM
Getting serious about routers loninappleton Everything Else 28 20th May 2008 12:40 AM
Jasper jig and metabo routers DIY_Peter Multi-Way 10 2nd August 2003 04:48 AM
newbie post, but hopefully not a newbie question wiredcur Solid State 3 24th August 2002 11:49 PM


New To Site? Need Help?

All times are GMT. The time now is 08:55 PM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2