Understanding Scope Trace Square Wave - diyAudio
Go Back   Home > Forums > Design & Build > Equipment & Tools
Home Forums Rules Articles diyAudio Store Gallery Wiki Blogs Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Equipment & Tools From test equipment to hand tools

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Thread Tools Search this Thread
Old 2nd August 2010, 02:20 AM   #1
diyAudio Member
Join Date: Jun 2008
Default Understanding Scope Trace Square Wave

I'm new to using a scope as diagnostic tool and would like to check my steps/ get some guidance. These shots are taken across the secondary of a preamp (10Y) line output transformer connected to the input of a 4 pole LC line level crossover with rated impedance of 5K Ohm. Am I right in thinking that the ringing from 2.5KHz. and up is caused by interaction of the inductors?
The 20Khz. Square is completely beyond me . . . . Can anybody help with some comments? Thanks.
Attached Images
File Type: jpg DSCF2747.jpg (590.2 KB, 342 views)
File Type: jpg DSCF2753.jpg (599.8 KB, 323 views)
File Type: jpg DSCF2755.jpg (562.9 KB, 318 views)
  Reply With Quote
Old 2nd August 2010, 02:23 AM   #2
diyAudio Member
Join Date: Jun 2008
3 more
Attached Images
File Type: jpg DSCF2760.jpg (592.3 KB, 309 views)
File Type: jpg DSCF2761.jpg (606.2 KB, 294 views)
File Type: jpg DSCF2762.jpg (591.1 KB, 112 views)
  Reply With Quote
Old 2nd August 2010, 02:42 AM   #3
diyAudio Member
Join Date: Apr 2003
Location: Southern Tier NY
Did you look at the signal being fed directly from the source? Make sure the square wave signal is clean. What is the output impedance of the linestage? The 5K load is pretty heavy.
Living Life Doing the Waltz in 4/4 meter.
  Reply With Quote
Old 2nd August 2010, 04:21 AM   #4
diyAudio Member
HollowState's Avatar
Join Date: Aug 2006
Location: Taxland, New Jersey
Here are a few basics for square wave testing, which is actually a form of pulse testing.

For best waveform quaility the output of your source generator should be terminated with it's characteristic output impedance. This is done at the far end of the coax cable where it meets the DUT. (device under test) An unterminated line will allow overshoot.

When testing a preamp (or any amp) it's output should be terminated in it's characteristic impedance with a non-inductive load resistor and nothing else. If unsure of the required output impedance, choose a typical working impedance that is reasonable. External L's and C's will grossly affect the waveform giving false indications of it's performance.

Now, the severe tilt at 100Hz is because your scope is rolling it off. Set the scope input to DC coupling. The drooping will flatten out.

Because a square wave is composed of many higher harmonics, for testing and analyzing purposes, they will equate upward by a factor of ten over the fundamental. This means that a frequency of 2500 to 3000Hz is the highest one should use when transformers are in the signal path. These will equate out to 25K and 30KHz respectively. Two frequencies are usually enough for a full range test. One low and one high. Remember for frequencies F10 (low) and Fx10 (high).

Some people will say to go ahead and use a 10KHz square wave just to see how good things really are. (or aren't) But you will be asking the transformer to pass 100KHz worth of harmonics which they won't do in most cases. So the rolled off and distorted leading corner will be of little meaning.

Circuit dampening is indicated by the shape at the top rising edge of the square wave. A well dampened circuit is shown by a waveform without overshoot. Poor dampening results in a train of oscillations after the inital rise. Waveforms with unequal positive and negative amplitudes indicates non-linear distortion. A rounded leading corner indicates poor HF response, while a downward tilting top and bottom means poor LF response.

Square wave testing should be done at a level well under the overload point of the DUT. An overloaded amp will make a square wave look better then it actually may be.
1944: 18 year olds storm the beach of Normandy into almost certain death.
2017: 18 year olds need a safe place because words hurt their feelings.

Last edited by HollowState; 2nd August 2010 at 04:48 AM. Reason: added text
  Reply With Quote
Old 2nd August 2010, 12:23 PM   #5
Merlinb is offline Merlinb  United Kingdom
diyAudio Member
Merlinb's Avatar
Join Date: May 2006
Location: Lancashire
Nice tutorial!

Originally Posted by HollowState View Post
Some people will say to go ahead and use a 10KHz square wave just to see how good things really are. (or aren't) But you will be asking the transformer to pass 100KHz worth of harmonics which they won't do in most cases. So the rolled off and distorted leading corner will be of little meaning.
I would suggests that this is still worth trying. A rolled-off leading edge suggests a better stability margin, and is more desirable than a leading edge which shows an overshoot or ringing.
  Reply With Quote
Old 3rd August 2010, 05:23 AM   #6
diyAudio Member
Join Date: Jun 2008
Thanks very much for your posts. It was very helpful. HollowState, you gave me everything I needed to get at it, many thanks.

I checked the Ramsey generator again and its output is very clean throughout its range. I also checked again using a 70Ohm resistor across its connection to the preamp but there was almost no change that I could see.

What made me feel it was time to stop doing everything by ear and start using test gear was the nasty little edge that was sort of tearing at the ear or making the scalp crawl. Last night I put the scope on the grid with the preamp turned off and got the first shot below. Wondering how rf was getting going so well with no power, tonight I changed the value of the grid stop resister and added a bead to it. I also put beads on the filament supply leads at the socket. This had a huge effect on sound though when I scoped it it looked almost the same. Then while noodling around on the scope controls I noticed that as I was switching from AC input to DC through the GND setting at center the trace briefly went clean. I then found it is possible to hold the switch at a point between the coupling and ground and then see a very clean trace. I'm not sure whether this means the scope has a problem or if holding the switch at a some midpoint is somehow filtering rf. My guess is that the scope is feeling its age and needs cleaning or servicing.

The big thing for me is both that I got started with the Oscilloscope and also that having put a couple of beads and a higher value grid stopper the sound is so utterly different that even my girlfriend stood there with her mouth open in surprise at the huge difference an apparently small change can make. It seems as if there is more gain as well, making me wonder if inaudible hf oscillation can lower the tube's gain. . . .

Pic 1 ) Signal at grid with preamp turned off. 2) Signal at output after bead and grid stopper added. 3) Same but with switch held in intermediate position.

If I get time tomorrow I'll do another full test of the preamp.

Thanks again ! ! !
Attached Images
File Type: jpg DSCF2764.jpg (693.0 KB, 95 views)
File Type: jpg DSCF2770.jpg (515.8 KB, 89 views)
File Type: jpg DSCF2771.jpg (538.5 KB, 83 views)
  Reply With Quote


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

Similar Threads
Thread Thread Starter Forum Replies Last Post
Scope trace more and more to one side iko Equipment & Tools 5 3rd May 2010 09:12 PM
Sine wave - Square & Triangle wave generator using Transistors / OP-Amps lineup Solid State 20 9th October 2006 12:15 AM
Microphone turns triangle wave into square wave? Circlotron Analogue Source 18 25th January 2003 06:44 AM

New To Site? Need Help?

All times are GMT. The time now is 01:42 PM.

vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999-2017 diyAudio

Content Relevant URLs by vBSEO 3.3.2