Speaker Turn On Delay and DC Protector Board Set (V2) - diyAudio
Go Back   Home > Forums > Commercial Sector > The diyAudio Store

The diyAudio Store A forum for discussing anything about the products available in The diyAudio Store.

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 7th June 2012, 05:43 AM   #1
Ana is offline Ana
diyAudio Member
 
Ana's Avatar
 
Join Date: Aug 2011
Default Speaker Turn On Delay and DC Protector Board Set (V2)

This thread is for discussions about the Speaker Turn-On Delay and DC Protector board (V2). This has now been superceeded by the V3 generation of the board which essentially is the same board with a different layout compatible with our 10x10 grid pattern.

Last edited by Jason; 10th December 2013 at 08:52 AM.
  Reply With Quote
Old 26th October 2012, 09:51 AM   #2
urosh is offline urosh  Slovenia
diyAudio Member
 
Join Date: Jul 2004
Location: Maribor
Default Monoblocks

Hi,

can speaker protector be used for monoblocks?

Is ok to just left out K2 and R12 and just use K1 with appropriate voltage?

Kind regards
Urosh
  Reply With Quote
Old 26th October 2012, 11:48 PM   #3
diyAudio Member
 
Join Date: Feb 2005
If you are considering a second run of the 'Soft Start' pcb, could you include a simple DC Trap, as any dc component is 'bad news' (for torroids especially) and is now common in all of our main supplies - just requires a couple of caps and diodes directly in line with the active mains line that's already on the board - plus, while the mains is so readily available, perhaps add a simple 'Line filter' to complete the set.
__________________
... jh
  Reply With Quote
Old 27th October 2012, 12:25 PM   #4
diyAudio Moderator
 
JojoD818's Avatar
 
Join Date: Mar 2003
Location: searching...
Thank you for your feedback.
  Reply With Quote
Old 27th October 2012, 12:25 PM   #5
diyAudio Moderator
 
JojoD818's Avatar
 
Join Date: Mar 2003
Location: searching...
Quote:
Originally Posted by urosh View Post
Hi,

can speaker protector be used for monoblocks?

Is ok to just left out K2 and R12 and just use K1 with appropriate voltage?

Kind regards
Urosh
Yes it will work. Yes again.
  Reply With Quote
Old 27th October 2012, 04:54 PM   #6
urosh is offline urosh  Slovenia
diyAudio Member
 
Join Date: Jul 2004
Location: Maribor
Quote:
Originally Posted by JojoD818 View Post
Yes it will work. Yes again.
Thank you
Urosh
  Reply With Quote
Old 2nd November 2012, 10:39 AM   #7
diyAudio Member
 
Join Date: Sep 2008
Default Use of DC Supply instead of AC

Hello,

If I want to use DC voltage :
- I don't need C6 and I can use a strap instead of D6,
- I must use K1-1 as the positiv and K2 for ground

Is that right ?

I have 12volts relays, what range of DC voltage can I use ?
How much current do I need ?

Thank You for your response.

Eric
  Reply With Quote
Old 2nd November 2012, 10:44 AM   #8
diyAudio Moderator
 
JojoD818's Avatar
 
Join Date: Mar 2003
Location: searching...
Quote:
Originally Posted by maillard View Post
Hello,

If I want to use DC voltage :
- I don't need C6 and I can use a strap instead of D6,
- I must use K1-1 as the positiv and K2 for ground

Is that right ?

I have 12volts relays, what range of DC voltage can I use ?
How much current do I need ?

Thank You for your response.

Eric
If you have available 12V to 15V DC then you don't need D6 and C6, but be mindful of the polarity when you do. Make sure the positive goes to the line going to D6 position. 500mA to 750mA should be more than enough.

I'm not sure what you mean by "I must use K1-1 as the positiv and K2 for ground"
  Reply With Quote
Old 2nd November 2012, 12:27 PM   #9
diyAudio Member
 
Join Date: Sep 2008
Sorry, I wanted to say : connect the positiv DC (12V to 15V) to X1-1 and connect the ground to X1-2.
Thank-You.
  Reply With Quote
Old 2nd November 2012, 12:42 PM   #10
diyAudio Moderator
 
JojoD818's Avatar
 
Join Date: Mar 2003
Location: searching...
Quote:
Originally Posted by maillard View Post
Sorry, I wanted to say : connect the positiv DC (12V to 15V) to X1-1 and connect the ground to X1-2.
Thank-You.
Yes that should work. But if your relays are rated 12V then you need 24V DC supply, not 12V-15V only as the relays will not engage.
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Speaker Turn On Delay and DC Protector Board Set (V3) Jason The diyAudio Store 44 12th June 2014 09:43 PM
Speaker delayed insertion, speaker protector, off set sensor destroyer X Solid State 35 2nd June 2014 06:01 PM
Standby mode and speaker turn on delay together? TiGeRGuY Chip Amps 9 6th September 2012 07:55 AM
DC protector ?? ping_31140 Pass Labs 9 18th January 2009 09:34 AM
DC-protector for Leach Super amp supernet Solid State 8 28th May 2002 05:57 PM


New To Site? Need Help?

All times are GMT. The time now is 09:14 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright ©1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2