PCM2707 Schematic Review

bacworth · 27th October 2006, 11:12 AM

Any ideas on what is wrong with the attached schematic. Fundamentally I intend on using the i2s interface, but as part of testing I have applied 5v to Vccr and ran Voutr into a opamp without sucess.

thanks

Alien8 · 27th October 2006, 11:33 AM

Quote:

I have applied 5v to Vccr

you may want to check the datasheet...
your pcm2707 is dead

bacworth · 27th October 2006, 11:45 AM

The usb receiver still detects it under xp when I attach and disconnect it. According to the datatsheet Vccr should be 3.3v if self powered is this correct???

Add: I just changed it over (on the same channel) to 3.3v and still no previal.

cheers...

Alien8 · 27th October 2006, 01:35 PM

check datasheet p29

I assume that is more or less what you've built.

Several pins have to be connected to a 3.3V supply in order for it to work. If you exceed 5V for these pins, you are very likely to destroy it.

A

bacworth · 28th October 2006, 04:21 AM

anyone???

dsavitsk · 28th October 2006, 04:27 AM

How are you powering it? I've not tried the analog out, but you can see a working schematic at http://www.ecp.cc/NOS-USB-DAC.html and some notes on powering it under the VR3 section at http://www.ecp.cc/HPDAC.html

-d

bacworth · 28th October 2006, 04:36 AM

self powered using LP2950CZ3.3 (datasheet link here ) for 3.3v, I will take a look at the notes... cheers

bacworth · 28th October 2006, 04:44 AM

Not 100% sure on this, but should SSPND be connected to 3.3v. I just noticed mine isn't and the HPDAC is? According to the datashet SSPND is an output.

fluckscapacitor · 5th May 2007, 07:38 PM

Quote:

Originally posted by bacworth
Not 100% sure on this, but should SSPND be connected to 3.3v. I just noticed mine isn't and the HPDAC is? According to the datashet SSPND is an output.

I know this is an old thread....but I too am scratching my head as to why every PCM270X schematic I see has SSPND connected to 3.3V. I have yet to build a device based on this chip yet, but it looks like the purpose of SSPND pin is just a flag, indicating suspend mode, that can then be used for whatever purpose (an LED, disabling/enabling other parts of the circuit, etc)

My guess is that someone misinterpreted this pin to cause the PCM270X to suspend when put LOW. And then about 20 people decided to copy this rather than reading the datasheet.

dsavitsk · 5th May 2007, 08:04 PM

You are correct. This is a harmless bug in the hpdac and it is noted in the instructions. I don't remember why I did this in the first place, but I think it was just a misreading of the datasheet.

27th October 2006, 01:35 PM	#4
Alien8 diyAudio Member Join Date: Mar 2004 Location: Leuven	check datasheet p29 I assume that is more or less what you've built. Several pins have to be connected to a 3.3V supply in order for it to work. If you exceed 5V for these pins, you are very likely to destroy it. A __________________ A8 If 'I' knew what I was doing, life would sure be easier...

28th October 2006, 04:27 AM	#6
dsavitsk diyAudio Member Join Date: Jan 2005 Location: Chicago	How are you powering it? I've not tried the analog out, but you can see a working schematic at http://www.ecp.cc/NOS-USB-DAC.html and some notes on powering it under the VR3 section at http://www.ecp.cc/HPDAC.html -d __________________ http://www.ecpaudio.com

5th May 2007, 08:04 PM	#10
dsavitsk diyAudio Member Join Date: Jan 2005 Location: Chicago	You are correct. This is a harmless bug in the hpdac and it is noted in the instructions. I don't remember why I did this in the first place, but I think it was just a misreading of the datasheet. __________________ http://www.ecpaudio.com

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
ADC Board - Any chance of some schematic review?	dmills	Parts	0	21st September 2008 03:26 PM
Pcm2707 Usb->i2s	Rocky	Digital Source	0	21st October 2005 01:35 AM
Please review schematic	dstockwell	Tubes / Valves	9	18th September 2005 05:17 PM
which USB to I2S cct for PCM2707?	sceglar	Digital Source	0	29th August 2005 01:23 PM
PCM2707 USB-->I2S how to use etc.	nl	Digital Source	4	5th August 2005 12:29 PM


	Please consider donating to help us continue to serve you. Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving

27th October 2006, 11:45 AM	#3
bacworth diyAudio Member Join Date: Dec 2001 Location: Australia	The usb receiver still detects it under xp when I attach and disconnect it. According to the datatsheet Vccr should be 3.3v if self powered is this correct??? Add: I just changed it over (on the same channel) to 3.3v and still no previal. cheers...

28th October 2006, 04:21 AM	#5
bacworth diyAudio Member Join Date: Dec 2001 Location: Australia	anyone???

28th October 2006, 04:36 AM	#7
bacworth diyAudio Member Join Date: Dec 2001 Location: Australia	self powered using LP2950CZ3.3 (datasheet link here ) for 3.3v, I will take a look at the notes... cheers

28th October 2006, 04:44 AM	#8
bacworth diyAudio Member Join Date: Dec 2001 Location: Australia	Not 100% sure on this, but should SSPND be connected to 3.3v. I just noticed mine isn't and the HPDAC is? According to the datashet SSPND is an output.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)

New To Site?	Need Help?
Register to Participate Search Privacy Statement Contact Us	Frequently Asked Questions Did you forget your password? Mark Forums Read