PCM1701 datasheet ?

Bernhard · 24th November 2005, 09:26 AM

Hi,

I have DCD1560 with 2 x PCM1701 K3 ( K3

) and look for datasheet....

jean-paul · 24th November 2005, 10:40 AM

You could try by asking politely if somebody has it for you.....

Bernhard · 24th November 2005, 10:58 AM

Please somebody have the datasheet for me ?

PTSOUNDLAB · 17th February 2009, 06:37 PM

Hello,

I would like to replace the opa I/V conversion on my DP8020 by a passive I/V with resistor.
My idea is to do like that

But I have a doubt about Ref DC and BPO DC
Does I let Ref DC connected to -Vcc and BPO DC to Ground via capacitor ?

Thank you in advance for any help

Regards

Pascal

PTSOUNDLAB · 17th February 2009, 09:42 PM

Hello,

I tested this on my Kenwood DP-8020. After the 220 ohms resistor I have a generic anode follower stage with 5703W tubes. The sound is very very good.

We need just to isolate the pin 13, put a resitror between this pin and ground and insert the 5703W stage.

Regards

Pascal

24th November 2005, 09:26 AM	#1
Bernhard diyAudio Member Join Date: Apr 2002 Location: Munich	PCM1701 datasheet ? Hi, I have DCD1560 with 2 x PCM1701 K3 ( K3 ) and look for datasheet....

24th November 2005, 10:40 AM	#2
jean-paul diyAudio Moderator Emeritus Join Date: Sep 2002 Location: The Netherlands	You could try by asking politely if somebody has it for you..... __________________ It's only audio

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Burr Brown PCM1701	mpopovics	Digital Source	2	12th March 2012 08:00 PM
Datasheet	shon35us	Chip Amps	3	9th March 2009 03:10 PM
Looking for datasheet	satelitis	Tubes / Valves	3	9th December 2005 08:20 PM
Datasheet	Piersma	Digital Source	3	29th January 2003 07:49 PM

New To Site?	Need Help?
Register to Participate Search Privacy Statement Contact Us	Frequently Asked Questions Did you forget your password? Mark Forums Read


	Please consider donating to help us continue to serve you. Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving

24th November 2005, 10:58 AM	#3
Bernhard diyAudio Member Join Date: Apr 2002 Location: Munich	Please somebody have the datasheet for me ?

17th February 2009, 06:37 PM	#4
PTSOUNDLAB diyAudio Member Join Date: Dec 2001 Location: FRANCE / TOULOUSE	Hello, I would like to replace the opa I/V conversion on my DP8020 by a passive I/V with resistor. My idea is to do like that But I have a doubt about Ref DC and BPO DC Does I let Ref DC connected to -Vcc and BPO DC to Ground via capacitor ? Thank you in advance for any help Regards Pascal

17th February 2009, 09:42 PM	#5
PTSOUNDLAB diyAudio Member Join Date: Dec 2001 Location: FRANCE / TOULOUSE	Hello, I tested this on my Kenwood DP-8020. After the 220 ohms resistor I have a generic anode follower stage with 5703W tubes. The sound is very very good. We need just to isolate the pin 13, put a resitror between this pin and ground and insert the 5703W stage. Regards Pascal

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)