TNT audio Marantz CD63 mods... - diyAudio
Go Back   Home > Forums > Source & Line > Digital Source

Digital Source Digital Players and Recorders: CD , SACD , Tape, Memory Card, etc.

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 31st January 2005, 10:45 PM   #1
Chris is offline Chris  Norway
diyAudio Member
 
Chris's Avatar
 
Join Date: Sep 2001
Location: NORWAY
Question TNT audio Marantz CD63 mods...

Hello...........

In the improvement of the digital electronics chapter there might be some typing errors on the website?

From the TNT site:

“Find RD01, RD04 (near the DAC-Chip) R117, R118, RF01 (near the Micro-Processor Chip - between that Chip and the Transport). They all look the same and stand out. I replaced these with 1mH miniature Chokes (14 Ohm DCR). These Chokes have a self-resonance of around 1MHz (my ones came from Maplin). They look like large resistors. Now 1MHz is not enough for us. We need to extend the effectiveness here to much higher frequencies. Enter three small Ferrite-Beads each (sold in bags of 10 for pennies). These are threaded onto the leads of the Choke, usefully extending the effectiveness to very high frequencies.”

R117 and R118 I think is wrong, maybe it should be R122, R123, R128 or R127 instead?

Also:
“As mentioned before, the Capacitors used by Marantz in the digital section are also nothing to write home about. So out go C126 (on the small board attached to the Transport), C157, C114, C120, CF02 (all 47uF 16V), to be replaced with Nichicon PL Series ultra low ESR Types."

C114 and C157 I think are wrong?

Thanks Chris
  Reply With Quote
Old 31st January 2005, 11:32 PM   #2
diyAudio Member
 
Join Date: Feb 2002
Location: Canada
I did my CD67 per the TNT site and I remember that I had to wing it alittle on some of the numbers. I just looked at the print and then at the PCB layout and I figured it out. All in all it's an excellent site and I'm very pleased with the results from my mods.

Regards,
Dan
  Reply With Quote
Old 1st February 2005, 04:46 PM   #3
Chris is offline Chris  Norway
diyAudio Member
 
Chris's Avatar
 
Join Date: Sep 2001
Location: NORWAY
Default 3 parts down and one to go....?

Thanks Dan for your reply..

I think I got it right now?

R117 and R118 should be R122 and R123. One of the capacitors should be C122 instead of C157 or C114.

I believe R122, R123,C120 and C122 "belong" together since they are parts for the TDA1301T (Q104) local powersupply.

Still one cap to go,,,,.. any ideas?

http://www.tnt-audio.com/clinica/cd67mods.html#digital
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Marantz CD63 with AES/EBU output mods Will Digital Source 4 10th April 2007 09:06 AM


New To Site? Need Help?

All times are GMT. The time now is 06:59 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright ©1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2