Problems with my DAC (CS8412)

meat · 2nd March 2004, 03:05 PM

I am trying to build a DAC from this schematic and I am not getting a signal from pin 26 (data out) I am also getting a high error flag on pin 25. I connected it in I2S mode like the site says, but something is not happy. I don't think the chip is bad, because it was barely working before I put it in the I2S mode. My guess is that something is connected wrong.

I have:

Pin 26 to Pin 3 of the TDA1543
Pin 24 to +5V
Pin 23 to GND
Pin 22 to +5V
Pin 21 to 1K resistor and - 47uf cap
Pin 20 to .047uf cap
Pin 18 to GND
Pin 17 to GND
Pin 13 to GND
Pin 12 to Pin 1 of TDA1543
Pin 11 to Pin 2 of TDA1543
Pin 10 to .01uf cap
Pin 9 to .01uf cap
Pin 8 to GND
Pin 7 to +5V

Any help would be appreciated

mpopovics · 2nd March 2004, 03:28 PM

Check out the configuration again.
Be sure, that from pin20 47nF and 1k resistor in series, and connected to the pin21, not to star GND.

47uF between pin22 and pin21
47uF between pin7 and pin8

Otherwise seems to be ok.
Check solder joints also...

BR,

meat · 2nd March 2004, 06:37 PM

Yeah, I checked and it is correct. I am getting data on pins 11 and 12, just not pin 26. I am probably not getting a signal lock, hence the error flag on pin 25.

meat · 4th March 2004, 09:23 PM

I got it working, the vector board is kind of lame and one of my pads was lifted.

mpopovics · 4th March 2004, 09:33 PM

Nice to hear, it is working.
BR,

2nd March 2004, 03:05 PM	#1
meat diyAudio Member Join Date: Jan 2004 Location: AZ	Problems with my DAC (CS8412) I am trying to build a DAC from this schematic and I am not getting a signal from pin 26 (data out) I am also getting a high error flag on pin 25. I connected it in I2S mode like the site says, but something is not happy. I don't think the chip is bad, because it was barely working before I put it in the I2S mode. My guess is that something is connected wrong. I have: Pin 26 to Pin 3 of the TDA1543 Pin 24 to +5V Pin 23 to GND Pin 22 to +5V Pin 21 to 1K resistor and - 47uf cap Pin 20 to .047uf cap Pin 18 to GND Pin 17 to GND Pin 13 to GND Pin 12 to Pin 1 of TDA1543 Pin 11 to Pin 2 of TDA1543 Pin 10 to .01uf cap Pin 9 to .01uf cap Pin 8 to GND Pin 7 to +5V Any help would be appreciated

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Cs8412	ManUtd	Digital Source	36	12th April 2011 12:27 AM
Help with Cs8412	NickC	Digital Source	0	6th January 2004 11:11 PM
FS: CS8412 and others	mdlover	Swap Meet	44	5th November 2003 09:37 PM
Wtb:cs8412 Dip	tone	Swap Meet	0	7th February 2003 08:56 AM

New To Site?	Need Help?
Register to Participate Search Privacy Statement Contact Us	Frequently Asked Questions Did you forget your password? Mark Forums Read


	Please consider donating to help us continue to serve you. Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving

2nd March 2004, 03:28 PM	#2
mpopovics diyAudio Member Join Date: Apr 2002 Location: Hungary	Check out the configuration again. Be sure, that from pin20 47nF and 1k resistor in series, and connected to the pin21, not to star GND. 47uF between pin22 and pin21 47uF between pin7 and pin8 Otherwise seems to be ok. Check solder joints also... BR,

2nd March 2004, 06:37 PM	#3
meat diyAudio Member Join Date: Jan 2004 Location: AZ	Yeah, I checked and it is correct. I am getting data on pins 11 and 12, just not pin 26. I am probably not getting a signal lock, hence the error flag on pin 25.

4th March 2004, 09:23 PM	#4
meat diyAudio Member Join Date: Jan 2004 Location: AZ	I got it working, the vector board is kind of lame and one of my pads was lifted.

4th March 2004, 09:33 PM	#5
mpopovics diyAudio Member Join Date: Apr 2002 Location: Hungary	Nice to hear, it is working. BR,

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)