Philips cd782 Issue - diyAudio
Go Back   Home > Forums > Source & Line > Digital Source

Digital Source Digital Players and Recorders: CD , SACD , Tape, Memory Card, etc.

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 27th February 2015, 07:14 PM   #1
diyAudio Member
 
Join Date: Sep 2008
Red face Philips cd782 Issue

Bought this player , and it was runing fine . So i thought it can be better . Changed some capacitors . Changed outpud op-amps . Those changes where not enought , sooo leets improve this player clock . I have tried a simple reclocking with mn74hcuo04 aaand everything was great really , this made huge improvement . I have listened to the player for some hours and at some point most of the ic`s became hot not that hot to burn but hot anyway . On the other day i turned the player again start playing it but i have noticed some noise from it and turned it off . I thought that reclocking went wrong and restored this player to factory mode , but nothing . What i have noted is that this player spins to fast *yes i checked that it might be SAA7220 issue bought new one and repleced it but nothing changed . Also i can hear laser head is banging on the disk when it is starting . I have changed nearest spindle motor transistors but nothing . So what might be wrong ?
__________________
http://ipetkow.olx.bg/ - Електронни компоненти .
  Reply With Quote
Old 27th February 2015, 07:45 PM   #2
Mike P is offline Mike P  United Kingdom
diyAudio Member
 
Join Date: Jan 2012
I had a similar problem once with an Arcam alpha 5, the turntable motor was spinning crazy fast and out of control. The problem turned out to be a bad connection with the SAA7220 which at the time was mounted in an IC socket. My best suggestion would be to check all solder joints and connections are good around this chip. Good luck!
  Reply With Quote
Old 27th February 2015, 07:48 PM   #3
Stabby is offline Stabby  Belgium
diyAudio Member
 
Join Date: Sep 2010
Did you build a separate supply/regulator for the SAA7220 without a heat sink?
  Reply With Quote
Old 27th February 2015, 07:56 PM   #4
diyAudio Member
 
Join Date: Sep 2008
Mike Thanks , i`ve alleready changed old SA7220 with new one ... so it is resoldered. Stabby no i was using existing one , and after this incident i have replaced it with new one just in case . I have similar player cd780 and i`m taking parts of it and using it on 782 , 780 one is in working order . So i have changed both player DF and 780 is working now . Also changed op amp on the servo motor.Trying to check TDA5709 , but no luck so far in measuring it .
__________________
http://ipetkow.olx.bg/ - Електронни компоненти .

Last edited by Krokotam_; 27th February 2015 at 08:01 PM.
  Reply With Quote
Old 27th February 2015, 07:59 PM   #5
Mike P is offline Mike P  United Kingdom
diyAudio Member
 
Join Date: Jan 2012
It's normal for the SAA7220 to get quite warm. Which other IC's got hot?
  Reply With Quote
Old 27th February 2015, 08:00 PM   #6
Mike P is offline Mike P  United Kingdom
diyAudio Member
 
Join Date: Jan 2012
Oh and did you make the mistake of using any very low ESR capacitors directly after voltage regulators?
  Reply With Quote
Old 27th February 2015, 08:08 PM   #7
diyAudio Member
 
Join Date: Sep 2008
No no new capacitors so far . I have learned this lesson with Marantz cd60 I have changed 12 volt diodes with shotky but this was at the time when the player was working so i doubt that this can harm it .
__________________
http://ipetkow.olx.bg/ - Електронни компоненти .

Last edited by Krokotam_; 27th February 2015 at 08:10 PM.
  Reply With Quote
Old 27th February 2015, 08:23 PM   #8
Stabby is offline Stabby  Belgium
diyAudio Member
 
Join Date: Sep 2010
What lesson did you learn exactly from your Marantz CD60? I'm about to change the caps in one of my players...
  Reply With Quote
Old 27th February 2015, 08:26 PM   #9
diyAudio Member
 
Join Date: Sep 2008
Stabby some times when using low esr caps you can provide more power to some ICs , this can destroy some of them , also more capacitance . But let`s stay to the topic I`m still unable to play anything on my cd .
__________________
http://ipetkow.olx.bg/ - Електронни компоненти .
  Reply With Quote
Old 28th February 2015, 06:44 AM   #10
diyAudio Member
 
Join Date: Sep 2008
So far nothing found ... i`ve watched to the lens and saw that knocking is from it banging at the end of the track , strange .
__________________
http://ipetkow.olx.bg/ - Електронни компоненти .
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Philips CDPRO 2 laser transport issue. Johnno Digital Source 0 28th January 2015 02:34 PM
philips cdm 4/11 noise issue tsudoit Digital Source 1 9th October 2014 09:25 PM
Philips cd101 relay issue? isitrisky Digital Source 11 19th April 2014 06:46 PM
CDM-0 / Philips CD-303 Hum issue tech_freak Digital Source 7 2nd October 2009 09:29 PM
Philips Magnavox FD1000 / CD100 'Humming' issue Raddek Digital Source 9 9th February 2009 11:15 PM


New To Site? Need Help?

All times are GMT. The time now is 03:21 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2015 DragonByte Technologies Ltd.
Copyright 1999-2015 diyAudio

Content Relevant URLs by vBSEO 3.3.2