Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Digital Source Digital Players and Recorders: CD , SACD , Tape, Memory Card, etc.

Tray don't stop by Primare CD20 and Thule CD-100 (both MK-1) after Switch-On
Tray don't stop by Primare CD20 and Thule CD-100 (both MK-1) after Switch-On
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Thread Tools Search this Thread
Old 4th December 2012, 06:43 PM   #1
tiefbassuebertr is online now tiefbassuebertr  Germany
diyAudio Member
tiefbassuebertr's Avatar
Join Date: Jul 2005
Location: D-55629 Schwarzerden
Default Tray don't stop by Primare CD20 and Thule CD-100 (both MK-1) after Switch-On

The tray goes several times in and out and then only in one direction without stop (tray motor turns below the belt).
Shorting the Tray end switch for stop changes nothing.

An exact analysis provides the following results:

1) No unwanted interrupt between the switch and the associated connections on the PCB

2)a. Between Tray-In (PIN 19, MCU 80C32 = U100 and R20 = 100K) and GND I observe 0V and 5VDC, if I swich on and off the tray end switch for stop shortly after switch on the mains switch. Thereafter (15 seconds) the voltage value at this place remains at 5VDC, independend of the position of this switch.

2)b. Between Tray-out (PIN 20, MCU 80C32 = U100 and R21 = 100K) and GND
there are always 0V

3) At the resonator is to observe the correct high frequency sine wave (PIN20/21-X1/X2)

4) there was several leaked SMD electrolytics on this PCB. This I have already removed and replaced by new ones. Also, I have thoroughly cleaned the board in those areas.

How can I prove whether the MCU IC (PLCC44 outline = plastic leaded chip carrier; 44 leads) is defective or if other things are still broken ??

Replace the MCU isn't easy, because there isn't a DIL or QFP outline.

How can I exactly check the right working of "RESET" and "EA/Vpp" (pins 10 and 35 - go to PLCC outline on page 4)?
Thank you very much for helping and advices.

In the attachement the associate schematics - here the MCU datasheet:
P80C32EBAA pdf, P80C32EBAA description, P80C32EBAA datasheets, P80C32EBAA view ::: ALLDATASHEET :::
Picture of the PCB you will find at post #24 here:

Last edited by tiefbassuebertr; 4th December 2012 at 07:09 PM.
  Reply With Quote


Tray don't stop by Primare CD20 and Thule CD-100 (both MK-1) after Switch-OnHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
PRIMARE A20 MK II no output gogosound Solid State 3 27th May 2010 02:58 AM
tray gear for CD-M4 and CD-M9 mdlover Swap Meet 70 22nd May 2009 02:50 PM
Sony CD-X33ES CD Tray not opening-help? eldarvanyar Digital Source 7 14th January 2008 06:12 PM
Marantz CD80 tray motor is running non-stop Jeph Digital Source 12 8th May 2006 03:23 PM
CD tray problem!!! Anorgan Digital Source 2 28th February 2004 11:47 PM

New To Site? Need Help?

All times are GMT. The time now is 09:19 PM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.00%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Copyright ©1999-2018 diyAudio