Tray don't stop by Primare CD20 and Thule CD-100 (both MK-1) after Switch-On - diyAudio
Go Back   Home > Forums > Source & Line > Digital Source
Home Forums Rules Articles diyAudio Store Gallery Wiki Blogs Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Digital Source Digital Players and Recorders: CD , SACD , Tape, Memory Card, etc.

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Thread Tools Search this Thread
Old 4th December 2012, 05:43 PM   #1
diyAudio Member
tiefbassuebertr's Avatar
Join Date: Jul 2005
Location: D-55629 Schwarzerden
Default Tray don't stop by Primare CD20 and Thule CD-100 (both MK-1) after Switch-On

The tray goes several times in and out and then only in one direction without stop (tray motor turns below the belt).
Shorting the Tray end switch for stop changes nothing.

An exact analysis provides the following results:

1) No unwanted interrupt between the switch and the associated connections on the PCB

2)a. Between Tray-In (PIN 19, MCU 80C32 = U100 and R20 = 100K) and GND I observe 0V and 5VDC, if I swich on and off the tray end switch for stop shortly after switch on the mains switch. Thereafter (15 seconds) the voltage value at this place remains at 5VDC, independend of the position of this switch.

2)b. Between Tray-out (PIN 20, MCU 80C32 = U100 and R21 = 100K) and GND
there are always 0V

3) At the resonator is to observe the correct high frequency sine wave (PIN20/21-X1/X2)

4) there was several leaked SMD electrolytics on this PCB. This I have already removed and replaced by new ones. Also, I have thoroughly cleaned the board in those areas.

How can I prove whether the MCU IC (PLCC44 outline = plastic leaded chip carrier; 44 leads) is defective or if other things are still broken ??

Replace the MCU isn't easy, because there isn't a DIL or QFP outline.

How can I exactly check the right working of "RESET" and "EA/Vpp" (pins 10 and 35 - go to PLCC outline on page 4)?
Thank you very much for helping and advices.

In the attachement the associate schematics - here the MCU datasheet:
P80C32EBAA pdf, P80C32EBAA description, P80C32EBAA datasheets, P80C32EBAA view ::: ALLDATASHEET :::
Picture of the PCB you will find at post #24 here:
Very strange fault (CD-player)

Last edited by tiefbassuebertr; 4th December 2012 at 06:09 PM.
  Reply With Quote


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

Similar Threads
Thread Thread Starter Forum Replies Last Post
PRIMARE A20 MK II no output gogosound Solid State 3 27th May 2010 01:58 AM
tray gear for CD-M4 and CD-M9 mdlover Swap Meet 70 22nd May 2009 01:50 PM
Sony CD-X33ES CD Tray not opening-help? eldarvanyar Digital Source 7 14th January 2008 05:12 PM
Marantz CD80 tray motor is running non-stop Jeph Digital Source 12 8th May 2006 02:23 PM
CD tray problem!!! Anorgan Digital Source 2 28th February 2004 10:47 PM

New To Site? Need Help?

All times are GMT. The time now is 03:54 PM.

vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999-2017 diyAudio

Content Relevant URLs by vBSEO 3.3.2