Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Digital Source Digital Players and Recorders: CD , SACD , Tape, Memory Card, etc.

Need help selecting an I2S/DSD/SPDIF connector for my impending Buffalo II
Need help selecting an I2S/DSD/SPDIF connector for my impending Buffalo II
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Thread Tools Search this Thread
Old 9th February 2010, 09:03 PM   #1
orpheus is offline orpheus  United States
diyAudio Member
Join Date: Jul 2004
Location: NYC
Default Need help selecting an I2S/DSD/SPDIF connector for my impending Buffalo II

I have been searching for information about I2S and DSD connections, and have not been able to get a handle on the requirements and limitations of the cables and hardware that can be used to make these connections.

I want to be able to connect a DSD output from an SACD player, SPDIF, and I2S to the Buffalo II board.

I had thought about using a switch to be able to connect all three to the buffalo, but then I realized that I could just switch by changing the cable, since any change would require powering down anyway. No switch would be easier and probably result in better sound.

Summary of ramblings below: 4 pin XLR, RJ45, 2 BNC's, or Lemo for DSD/I2S cable and input connector?

The easiest way I can think of (and using what I have on hand, which is always easiest) would be to connect a BNC to the SPDIF input and ground, and then a 4 pin XLR to the 3 I2S/DSD inputs, and share the ground connection between the BNC and the 4 pin XLR. This way I would have all the inputs covered with two connectors.

I could use two more BNC's instead (for a total of 3 BNC's between DSD/I2S and SPDIF), but that would lead to more complicated cable making (which I don't mind if it would function better).

I could also use LEMO connectors, would these be better than a 4 pin XLR for digital signals? The LEMO's would cost more, but I would spend the money if it would be a much better digital connection.

I could also try to implement an RJ45 connector for the DSD/I2S, in which case I would be sharing the ground with the SPDIF BNC. Is this a better connector? In some ways this would be easiest because I could just use already built ethernet cables to make the connection. There are panel mount RJ45 connectors on Digikey, but I can't tell how difficult it would be to solder the cables to the connector.

Would any problems result from sharing the ground connection between a BNC on the SPDIF connection and the ground connection with the DSD/I2S input?

I am open to suggestions if anyone has one. I am not an EE or very knowledgeable about the requirements of digital connections, so any help is greatly appreciated.

I have read that Cat5 cable is supposed to be best for DSD, does the same hold true for I2S? I had read that I could run about 1.5 meters of DSD cabling and be OK, and about the same for I2S. Is this true?

Thank you for reading my ramblings. I appreciate your time and consideration in offering assistance.

  Reply With Quote


Need help selecting an I2S/DSD/SPDIF connector for my impending Buffalo IIHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Buffalo II Russ White Twisted Pear 1912 7th December 2017 04:35 AM
i2s/DSD over longer distances: line drivers to spare NeoY2k Digital Line Level 8 3rd October 2008 01:05 PM
I2s --> SPDIF out ? intuit Digital Source 5 8th March 2004 03:36 AM
Where can I get the spec. of the I2S and SPDIF standard ? intuit Digital Source 0 4th March 2004 08:45 AM
I2S to SPDIF Circuit help longaniza Digital Source 6 15th April 2003 07:16 AM

New To Site? Need Help?

All times are GMT. The time now is 08:10 PM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.79%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Copyright ©1999-2018 diyAudio