Finally, an affordable CD Transport: the Shigaclone story - Page 110 - diyAudio
Go Back   Home > Forums > Source & Line > Digital Source

Digital Source Digital Players and Recorders: CD , SACD , Tape, Memory Card, etc.

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 28th May 2008, 07:57 PM   #1091
johnm is offline johnm  United Kingdom
diyAudio Member
 
johnm's Avatar
 
Join Date: Sep 2003
Location: Hampshire
Okapi, I have a motor here which you're welcome to. Problem is it would take a while to get to you as I'd be posting from UK.

Let me know. john underscore s underscore may AT hotmail dot com. (no spaces anywhere)

- John
  Reply With Quote
Old 28th May 2008, 08:03 PM   #1092
hayenc is offline hayenc  United States
diyAudio Member
 
hayenc's Avatar
 
Join Date: Apr 2005
Location: Glendale, AZ
Send a message via Yahoo to hayenc
If you are looking for motor, lens, mechanism, etc. you might try eBay: Item: 360032600671 or 270237172878
  Reply With Quote
Old 28th May 2008, 08:27 PM   #1093
okapi is offline okapi  United States
diyAudio Member
 
okapi's Avatar
 
Join Date: Aug 2004
Location: Buffalo
Quote:
Originally posted by hayenc
If you are looking for motor, lens, mechanism, etc. you might try eBay: Item: 360032600671 or 270237172878
thanks for the info. i did not want to spend $60 for a motor.

to the best of your knowledge, can you confirm that i could swap the disc motor off of either of the eBay units for the one in the jvc player?

thanks again
  Reply With Quote
Old 28th May 2008, 09:17 PM   #1094
hayenc is offline hayenc  United States
diyAudio Member
 
hayenc's Avatar
 
Join Date: Apr 2005
Location: Glendale, AZ
Send a message via Yahoo to hayenc
At this point I only have a visual that the motors look identical. There are two solder tabs that would have to be removed to make the replacement, but I have not had a chance to do any other measurements on them.
  Reply With Quote
Old 29th May 2008, 01:32 AM   #1095
hayenc is offline hayenc  United States
diyAudio Member
 
hayenc's Avatar
 
Join Date: Apr 2005
Location: Glendale, AZ
Send a message via Yahoo to hayenc
Wrote that last one quickly at work. To clarify, I did buy a 16 pin version as that is how many pins I counted on the laser and in the service manual, and physically compared them side by side. The eBay one does not have a part number on it like the one in the EZ31, but they do look identical.
  Reply With Quote
Old 29th May 2008, 01:48 AM   #1096
diyAudio Member
 
Algar_emi's Avatar
 
Join Date: Oct 2002
Location: Canada, Qc
BoilermakerFan you have mail. Don't forget, this is my last unit.
  Reply With Quote
Old 29th May 2008, 07:55 AM   #1097
diyAudio Member
 
Join Date: Apr 2008
Quote:
Originally posted by Peter Daniel
When suspending mechanism from the bottom, using two spacers like this worked better than direct mount:

Click the image to open in full size.

Peter, Do u mean using this for each pole--4 for the 2 poles? Where do u buy this?
  Reply With Quote
Old 29th May 2008, 02:15 PM   #1098
diyAudio Member
 
Peter Daniel's Avatar
 
Join Date: Jul 2002
Location: Toronto, Canada
Send a message via AIM to Peter Daniel
In my experience mounting the mechanism plate on two poles (either supported or suspended) sounded better than on all four.

The part in a picture is modified aircraft bushing. You may use regular washer instead.
__________________
www.audiosector.com
“Do something really well. See how much time it takes. It might be a product, a work of art, who knows? Then give it away cheaply, just because you feel that it should not cost so much, even if it took a lot of time and expensive materials to make it.” - JC
  Reply With Quote
Old 29th May 2008, 05:47 PM   #1099
diyAudio Member
 
JC Fardo's Avatar
 
Join Date: Jun 2002
Location: Sao Paulo - Brazil
Quote:
Originally posted by Peter Daniel
As I was working recently on a new display board, here's the actual schematic, the one in service manual is not exactly accurate.

I also simplified it for my needs, with only 4 main buttons. The other 2 buttons are for programming and repeat. I only need them on remote.

The digital output resistors are also explaned there.
Peter and others who finished the transport, please

If you made a new frontal panel you need to connect the remote receiver, display and push bottons boards back to main PCB.

Did you keep original single row socket and ribbon cable or made it with single wires.

Thanks
__________________
JC
  Reply With Quote
Old 29th May 2008, 05:59 PM   #1100
diyAudio Member
 
Peter Daniel's Avatar
 
Join Date: Jul 2002
Location: Toronto, Canada
Send a message via AIM to Peter Daniel
Quote:
Originally posted by JC Fardo
Did you keep original single row socket and ribbon cable or made it with single wires.
Because of the way the display is integrated into wooden platform, I did it with a set of single wires: http://www.diyaudio.com/forums/showt...85#post1479885

Click the image to open in full size.
__________________
www.audiosector.com
“Do something really well. See how much time it takes. It might be a product, a work of art, who knows? Then give it away cheaply, just because you feel that it should not cost so much, even if it took a lot of time and expensive materials to make it.” - JC
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off



New To Site? Need Help?

All times are GMT. The time now is 10:00 PM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright ©1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2