CSS large kits coming - diyAudio
Go Back   Home > Forums > Commercial Sector > Manufacturers > CSS

CSS Creative Sound Solutions (CSS) is a service-oriented provider of high-value speaker components for the DIY loudspeaker builder

Reply
 
Thread Tools Search this Thread
Old 25th September 2012, 11:56 PM   #1
RAW is offline RAW  Canada
diyAudio Member
 
Join Date: Jul 2002
Location: British Columbia ,Canada
Default CSS large kits coming

In the works a few more designs with the CSS wave guide plus this new driver

Click the image to open in full size.
Click the image to open in full size.

Side by side with the VWR and the new driver coming in some kits

Click the image to open in full size.

rear view of both drivers
Click the image to open in full size.

In the works right now are
MT large monitor ;0
MTM
MLT just to name a few.
  Reply With Quote
Old 26th September 2012, 01:31 AM   #2
badman is offline badman  United States
diyAudio Member
 
badman's Avatar
 
Join Date: Sep 2003
Location: Sunny Tustin, SoCal
CSS- more info on waveguide? Woofer?
__________________
I write for www.enjoythemusic.com in the DIY section. You may find yourself getting a preview of a project in-progress. Be warned!
  Reply With Quote
Old 26th September 2012, 02:26 AM   #3
RAW is offline RAW  Canada
diyAudio Member
 
Join Date: Jul 2002
Location: British Columbia ,Canada
UH205PW1
Monster driver
• Underhung voice coil• Linear frequency response• Ultra low distortion• FEA Optimized motor• Pressed paper cone • Vented pole piece• Dual shorting rings
• Precision machined undercut pole piece• Aerodynamic basket design• Acoustically transparent spider• Vented voice coil • Symmetrical lead wire placement• Gold plated terminals• Die cast aluminum basket

http://motusaudio.com/wp-content/upl...eet-7-2012.pdf

On the wave guide Bob has them for sale but info I am not sure about.Look around the site.
  Reply With Quote
Old 26th September 2012, 03:15 PM   #4
diyAudio Member
 
tuxedocivic's Avatar
 
Join Date: Jan 2011
Location: Ladysmith, BC
Here's my take on the waveguide: New Drivers: VWR126X and LD25X

Planet 10 and I are working on these:

Click the image to open in full size.

So far so good. That's a temporary listening area though. Need to get them into a better spot.
  Reply With Quote
Old 26th September 2012, 04:47 PM   #5
frugal-phile(tm)
diyAudio Moderator
 
planet10's Avatar
 
Join Date: Oct 2001
Location: Victoria, BC, NA, Sol III
Blog Entries: 5
P10 has done its bit on those (Chris dd a fantastic job of repurposing of the original uFonkenWoof), Ryan is working his XO magic.

dave
__________________
community sites t-linespeakers.org, frugal-horn.com, frugal-phile.com ........ commercial site planet10-HiFi
p10-hifi forum here at diyA
  Reply With Quote
Old 26th September 2012, 07:14 PM   #6
RAW is offline RAW  Canada
diyAudio Member
 
Join Date: Jul 2002
Location: British Columbia ,Canada
The new monitor using these drivers will be 11" wide , with 1" cabinet walls bracing, 1.25" fronts.
  Reply With Quote
Old 26th September 2012, 09:36 PM   #7
chrisb is offline chrisb  Canada
diyAudio Member
 
Join Date: Aug 2002
Location: victoria BC
Quote:
Originally Posted by RAW View Post
The new monitor using these drivers will be 11" wide , with 1" cabinet walls bracing, 1.25" fronts.

can't wait to hear these - I'd definitely want to devise some type of yoke/cradle support for the magnets on those monster 8" drivers
__________________
you don't really believe everything you think, do you?
community sites t-linespeakers.org, frugal-horn.com commercial site planet10-HiFi
  Reply With Quote
Old 26th September 2012, 11:28 PM   #8
frugal-phile(tm)
diyAudio Moderator
 
planet10's Avatar
 
Join Date: Oct 2001
Location: Victoria, BC, NA, Sol III
Blog Entries: 5
Quote:
Originally Posted by RAW View Post
The new monitor using these drivers will be 11" wide , with 1" cabinet walls bracing, 1.25" fronts.
MDF or plywood?

dave
__________________
community sites t-linespeakers.org, frugal-horn.com, frugal-phile.com ........ commercial site planet10-HiFi
p10-hifi forum here at diyA
  Reply With Quote
Old 27th September 2012, 04:08 AM   #9
RAW is offline RAW  Canada
diyAudio Member
 
Join Date: Jul 2002
Location: British Columbia ,Canada
What every someone uses for construction is up to them.If they want to use MDF go a head, if you want to use baltic birch or bamboo this option is up to who ever purchases a kit.Sure the same cabinet construction applies with any kit someone purchases from any company.
  Reply With Quote
Old 27th September 2012, 04:13 AM   #10
RAW is offline RAW  Canada
diyAudio Member
 
Join Date: Jul 2002
Location: British Columbia ,Canada
The new monitor using these drivers will be 11" wide X 13" depth X 22" , with 1" cabinet walls bracing, 1.25" fronts.Slot port is out the rear of the cabinet.
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
New Kits Coming Soon!! CSS/XBL CSS 2 10th October 2012 09:15 PM
CSS FR125S, Alpair 7 & CSS EL70? Monte Verdi Markaudio 6 29th June 2010 08:51 PM
FS: Large inductors, Large Ports, and Leaky Holes luvdunhill Swap Meet 10 6th March 2009 03:01 PM
Large Cone/large VC or several medium sized cones / medium VCs vajolet Multi-Way 14 3rd December 2007 06:10 PM


New To Site? Need Help?

All times are GMT. The time now is 06:58 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2