diyAudio

diyAudio (http://www.diyaudio.com/forums/)
-   CSS (http://www.diyaudio.com/forums/css/)
-   -   CSS large kits coming (http://www.diyaudio.com/forums/css/220399-css-large-kits-coming.html)

RAW 25th September 2012 11:56 PM

CSS large kits coming
 
In the works a few more designs with the CSS wave guide plus this new driver

http://farm9.staticflickr.com/8033/8...2e7c4dd6_c.jpg
http://farm9.staticflickr.com/8032/8...a9a1b7b6_c.jpg

Side by side with the VWR and the new driver coming in some kits

http://farm9.staticflickr.com/8458/8...e7fe5837_c.jpg

rear view of both drivers
http://farm9.staticflickr.com/8035/8...b7ba83d8_z.jpg

In the works right now are
MT large monitor ;0
MTM
MLT just to name a few.

badman 26th September 2012 01:31 AM

CSS- more info on waveguide? Woofer?

RAW 26th September 2012 02:26 AM

UH205PW1
Monster driver
• Underhung voice coil• Linear frequency response• Ultra low distortion• FEA Optimized motor• Pressed paper cone • Vented pole piece• Dual shorting rings
• Precision machined undercut pole piece• Aerodynamic basket design• Acoustically transparent spider• Vented voice coil • Symmetrical lead wire placement• Gold plated terminals• Die cast aluminum basket

http://motusaudio.com/wp-content/upl...eet-7-2012.pdf

On the wave guide Bob has them for sale but info I am not sure about.Look around the site.

tuxedocivic 26th September 2012 03:15 PM

Here's my take on the waveguide: http://www.diyaudio.com/forums/css/2...ml#post3039888

Planet 10 and I are working on these:

http://i874.photobucket.com/albums/a...6072505A37.jpg

So far so good. That's a temporary listening area though. Need to get them into a better spot.

planet10 26th September 2012 04:47 PM

P10 has done its bit on those (Chris dd a fantastic job of repurposing of the original uFonkenWoof), Ryan is working his XO magic.

dave

RAW 26th September 2012 07:14 PM

The new monitor using these drivers will be 11" wide , with 1" cabinet walls bracing, 1.25" fronts.

chrisb 26th September 2012 09:36 PM

Quote:

Originally Posted by RAW (Post 3180147)
The new monitor using these drivers will be 11" wide , with 1" cabinet walls bracing, 1.25" fronts.


can't wait to hear these - I'd definitely want to devise some type of yoke/cradle support for the magnets on those monster 8" drivers

planet10 26th September 2012 11:28 PM

Quote:

Originally Posted by RAW (Post 3180147)
The new monitor using these drivers will be 11" wide , with 1" cabinet walls bracing, 1.25" fronts.

MDF or plywood?

dave

RAW 27th September 2012 04:08 AM

What every someone uses for construction is up to them.If they want to use MDF go a head, if you want to use baltic birch or bamboo this option is up to who ever purchases a kit.Sure the same cabinet construction applies with any kit someone purchases from any company.

RAW 27th September 2012 04:13 AM

The new monitor using these drivers will be 11" wide X 13" depth X 22" , with 1" cabinet walls bracing, 1.25" fronts.Slot port is out the rear of the cabinet.


All times are GMT. The time now is 06:27 PM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio


Content Relevant URLs by vBSEO 3.3.2