Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Construction Tips Construction techniques and tips

What would you call this part/technique?
What would you call this part/technique?
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Thread Tools Search this Thread
Old 25th July 2011, 12:42 AM   #1
hlzr is offline hlzr  United States
diyAudio Member
Join Date: Jul 2011
Default What would you call this part/technique?

So my friend has a Yamaha C-80 that had a scratchy pot we were replacing. When I looked inside, I saw all sorts of copper plates to conduct current which were installed in a through-hole fashion. Net result looked really clean and probably able to handle some serious power.

I found a thread on another site that shows what I am talking about:

Yamaha Control Amplifier C-80: Sick! (pics)

I'm thinking about using this construction technique for some instrument amplifiers I want to build (and maybe later some hi-fi gear after that); does anybody know if I can buy those copper pieces pre-cut like that or what the technique is called?

  Reply With Quote
Old 25th July 2011, 02:36 AM   #2
anatech is online now anatech  Canada
diyAudio Moderator
anatech's Avatar
Join Date: Jun 2004
Location: Georgetown, On
What would you call this part/technique?
Hi hlzr,
That is a very good way to run power and ground. The material has a far larger cross sectional area and runs pretty much directly where you want it. You can also run other non-current carrying ground conductors to form an shield.

Yamaha did this often, as have many other manufacturers over time. I did warranty work for Yamaha, among others. This is a common sight for me.

The technique, or "part" is called a bus. No surprise there. I have never seen anything for sale since the legs will enter the PCB at random places to suit your build. All you need to do is use sheet copper and cut out the areas not going through the PCB. You can either remove the material between the notches, or fold them up if the sheet is thin enough. You can also use Al bar stock, but fasten electrical connections with a screw, ring terminal and toothed washer on a surface off the PCB. Screws can be used to fasten the bar to the PCB, but don't rely on that for electrical connections. You can also use ring terminals meant for soldering to wire. Mount the rings to the bar loosely, feed the ends of the ring terminals down through the PCB and solder them. Then you can release the bar and mount it later on, or fasten it right afterwards. Loose mounting to begin limits heat loss into the bar.

"Just because you can, doesn't mean you should" my Wife
  Reply With Quote
Old 25th July 2011, 11:47 AM   #3
marce is offline marce  United Kingdom
diyAudio Member
Join Date: Jun 2007
Location: Blackburn, Lancs
Buzz bar cos by the time youv'e overloaded them they buzz!
  Reply With Quote


What would you call this part/technique?Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Need part # for 30-pin connector part inside Logitech Transporter on front panel PCB Bellatone Digital Source 4 27th April 2011 07:39 PM
Construction technique? g(f(e)) Tubes / Valves 1 27th January 2008 04:06 AM
what part can take the place of ST part VB408B completely peterchen88 Parts 0 8th September 2007 05:45 AM
I don't even know what to call this- Conrad Hoffman Everything Else 16 24th June 2007 04:11 PM
wiring technique... mattcaton88888 Car Audio 6 9th February 2006 03:10 PM

New To Site? Need Help?

All times are GMT. The time now is 01:33 PM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.79%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright ©1999-2017 diyAudio