Any easy way to lower V on SMPS500R-Single? - diyAudio
Go Back   Home > Forums > Commercial Sector > Vendor Forums > Inactive Vendor Forums > Connexelectronic

Connexelectronic Commercial Vendors large & small hawking their wares

 
 
Thread Tools Search this Thread
Old 7th March 2013, 02:03 AM   #1
JZatopa is offline JZatopa  United States
diyAudio Member
 
Join Date: May 2003
Location: Chicago
Default Any easy way to lower V on SMPS500R-Single?

I recently ordered a SMPS500R-Single 48V SMPS. It turns out that I should have ordered the 36V version. Does anyone here know if there is an easy way to modify my SMPS so it will output a lower V?
 
Old 7th March 2013, 02:58 AM   #2
gootee is offline gootee  United States
diyAudio Member
 
Join Date: Nov 2006
Location: Indiana
Blog Entries: 1
Is there a schematic somewhere?
 
Old 7th March 2013, 05:11 AM   #3
JZatopa is offline JZatopa  United States
diyAudio Member
 
Join Date: May 2003
Location: Chicago
There is one here

http://www.connexelectronic.com/documents/SMPS500R.pdf
 
Old 8th March 2013, 03:53 AM   #4
Cristi is offline Cristi  Europe
diyAudio Member
 
Join Date: Dec 2008
Location: Dortmund+Shenzhen
Due to topology used there is no easy way to change the output voltage within more than 10% limits without affecting it's performances or reliability. with classic, PWM power supplies either HB or Flyback, the output voltage can be adjusted to half or even lower with simple modification, usually just one two resistors. but these power supplies, 'R series, are optimized for efficiency and minimal noise so different topology is used which does not allow major deviation for output voltage. the only way to change it is to change the transformer, and few components from feedback loop.
special attention is required and know this fact when order them as sometimes buyers are chosing a higher or lower voltage version thinking that later might be used for another project with minimum changes which is not always possible.
__________________
www.connexelectronic.com complete assembled amplifier and SMPS
 
Old 8th March 2013, 03:54 PM   #5
JZatopa is offline JZatopa  United States
diyAudio Member
 
Join Date: May 2003
Location: Chicago
Thanks for the info Cristi. I guess I will just have to order another SMPS and find a new project for this one.

Anyone know of a good project to use a single rail 48V smps on?
 

 


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
SMPS300R or SMPS500R for UCD400 CrashHouse Power Supplies 2 21st March 2012 12:20 PM
Using 4 x l15d with SMPS500R edinm Class D 1 14th March 2012 03:35 PM
Pushing SINGLE Pair of MJL4281A/4302A to the max limits at lower impedance EWorkshop1708 Solid State 26 21st June 2011 03:09 PM
Connex SMPS500R-Single Power Supply SoldierAnt76 Swap Meet 0 3rd May 2011 12:49 AM
TA30320 & SMPS500R - help needed abbymat2 Class D 5 15th November 2010 06:00 AM


New To Site? Need Help?

All times are GMT. The time now is 12:14 PM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2