Switched Mode Power Supplies (SMPS) - Page 65 - diyAudio
Go Back   Home > Forums > Commercial Sector > Vendor Forums > Inactive Vendor Forums > Connexelectronic

Connexelectronic Commercial Vendors large & small hawking their wares

 
 
Thread Tools Search this Thread
Old 3rd November 2013, 10:48 AM   #641
alkasar is offline alkasar  France
diyAudio Member
 
Join Date: Jan 2009
Location: near Paris, France
Quote:
Originally Posted by Cristi View Post
Al, please use a 2 components epoxy which can settle in less than one hour to secure the core of the transformer.
Thanks Cristi
SMPS works perfectly well. Not noisy except when in the sub. The sub vibrations makes the transformer frame vibrate.

I am not sure where exactly to put the glue...
Click the image to open in full size.
a lot, as shown with the two blue lines to fill the gap ?
or a little glue, in the corners only for better heat dissipation ?

ps: I sent you another email address to reach me.
 
Old 4th November 2013, 03:48 AM   #642
diyAudio Member
 
Esperado's Avatar
 
Join Date: Jul 2011
Location: France
Quote:
Originally Posted by Cristi View Post
I always get that error with message not delivered from "Mail Delivery Subsystem"
Tring to get a new password on your web site, to write a (positive) review for one of your SMPS, i asked for a new password. 5 times. While you web site says " Success: A new password has been sent to your e-mail address.", i never received any.
And, yes, my POP3 mail server works perfectly.
__________________
Ultimate Protection and more.The Only Source of Knowledge is experience, everything else is just information” ©A. Einstein

Last edited by Esperado; 4th November 2013 at 03:52 AM.
 
Old 6th November 2013, 08:08 PM   #643
diyAudio Member
 
maxlorenz's Avatar
 
Join Date: Oct 2003
Location: osorno , Chile
Dear Cristi,

I just bought a pair of your 500W SMPS (QR and R) but was not patient enough to wait for answers to several questions I had...now that I found this thread, I will abuse of your kindness:

1) What is the difference between R and QR?
2) What is the expected ripple output with, say +/-36VDC?
In other words, would I benefit from a power regulator after them?
3) Which of your SMSP have extra aux. low voltage outputs?

Thank you very much.
M.
 
Old 6th November 2013, 08:55 PM   #644
diyAudio Member
 
maxlorenz's Avatar
 
Join Date: Oct 2003
Location: osorno , Chile
Quote:
Originally Posted by Esperado View Post
Projet : Ampli à base de LME49830 - "Gran Torino 150" - Page 49 - Amplification.
He had done it with a simple mesh metallic plate.
It was an amusing thread to read for me, because he was searching a power supply noise problem, when it was evident from the beginning this was an RFI problem on the input line of his amplifier, coming from the SMPS.
Note that he got, with twisted power wires between SMPS and Amplifier: 32mV of noise, not so bad ? JWithout twisted wires, it was 37.5mV .
OK. I found a very good answer to question nº2 from dear Esperado, post #295.
Merci bien, mon cher.
 
Old 7th November 2013, 06:28 AM   #645
glt is offline glt  United States
diyAudio Member
 
Join Date: Oct 2004
"R" is resonant design as in "soft switching". QR is "quasi-resonant" design as in "not so soft switching". Mainly "soft switching reduces RF noise. See this for additional info: Connex SMPS300RE | H i F i D U I N O
__________________
www.hifiduino.wordpress.com
 
Old 7th November 2013, 09:50 AM   #646
diyAudio Member
 
maxlorenz's Avatar
 
Join Date: Oct 2003
Location: osorno , Chile
Thank you!
 
Old 9th November 2013, 09:06 AM   #647
Cristi is offline Cristi  Europe
diyAudio Member
 
Join Date: Dec 2008
Location: Dortmund+Shenzhen
Esperado, please try to create a new account. I tried and cannot find a way to reset the pasword. the website sw is old and lacks of many functions.
Maxlorenz, I will try to answer to your questions in the same order:
1. SMPSxxxR - Resonant, LLC topology, fully regulated and adjustable output voltage. SMPSxxxQR - Quasi Resonant topology unregulated output voltage, proportional with mains input voltage and 5-10% variable from low load to full load. Main advantage, the SMPS200QR, SMPS240QR, SMPS300QR, SMPS3K6QR and SMPS4k8QR have the highest efficiency, about 1.5-2% higher than similar power resonant, regulated SMPS with same output power and at least 7-10% higher efficiency and 12-18dB lower switching noise compared with other similar SMPS on the market offered by competitors. Since it's output voltage is unregulated is suitable for amplifiers with higher PSRR.
2. For R series, is within tens of milivolts range, up to 100mV for highest output voltage versions. For QR series, there is a high-frequecy ripple component with similar amplitude as for R series, tens of mV, overimposed on mains freq. ripple, 100 or 120Hz due to the fact that the output voltage is not regulated and follow mains voltage variations. Before throwing stones at me, make sure you fully understand these terms, and you compared with these information with competitors offerings, 80-90% of them are offering unregulated SMPS only, often with much lower efficiency and worse EMI values.
3. All SMPS have at least one aux. voltage output, some of them are aditionally regulated using LM78xx regulators.
__________________
www.connexelectronic.com complete assembled amplifier and SMPS
 
Old 9th November 2013, 12:21 PM   #648
diyAudio Member
 
maxlorenz's Avatar
 
Join Date: Oct 2003
Location: osorno , Chile
Thank you very much dear Cristi.

Everything understood. Good options. I'll let you know my impressions.

Regards,
M.
 

 


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
switched-mode power suppies Dimitar13 Everything Else 0 19th February 2008 12:50 AM
PFC Switched-Mode Power Supply N-Channel Power Supplies 57 13th June 2005 07:56 PM
Switched mode power supply MMicke Car Audio 3 19th February 2005 10:42 AM
Switched mode power supplies Magura Parts 13 3rd January 2004 05:44 PM
Switched Mode vs Linear Power Supply royalmp2001 Solid State 4 12th July 2002 08:04 PM


New To Site? Need Help?

All times are GMT. The time now is 07:02 PM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright ©1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2