Class D Audio Amplifiers - Page 17 - diyAudio
Go Back   Home > Forums > Commercial Sector > Vendor Forums > Inactive Vendor Forums > Connexelectronic

Connexelectronic Commercial Vendors large & small hawking their wares

 
 
Thread Tools Search this Thread
Old 27th September 2012, 01:59 AM   #161
diyAudio Member
 
Join Date: Dec 2008
Location: Hong Kong or Europe
yes. same supply voltage for 200W on 8R or 400W on 4R. same gain for stereo module too.
__________________
www.connexelectronic.com complete assembled amplifier and SMPS
 
Old 27th September 2012, 03:16 PM   #162
4real is offline 4real  Netherlands
diyAudio Member
 
Join Date: May 2004
Location: Arnhem
Thanks Cristi, I think I'll go for the (4x) stereo modules with SMPS800R@60V PSU (2x)... I will probably be ordering in a few weeks, can't wait to compare with my current UcD400
 
Old 28th September 2012, 07:43 AM   #163
zog666 is offline zog666  Australia
diyAudio Member
 
Join Date: May 2009
That CxD250-HP amp modules looks really nice, I enjoy my lower cost irs2092 modules from another vendor (powered by a Connex SMPS), these look even better.
__________________
audio project blog http://www.minirig.org.au/
 
Old 28th October 2012, 07:52 AM   #164
diyAudio Member
 
Join Date: Apr 2004
Location: Gold Coast, Australia
Hi Cristi, I've received my four CxD300-8R modules and my two smps500r power supplies - thanks. I plan to install two modules and one power supply in each of my active speakers. Do you recommend putting the electronics in a metal enclosure or can I just bolt them all to one of the wooden inside walls of each speaker?
__________________
Now working on a budget Line Array.
 
Old 3rd November 2012, 02:57 PM   #165
diyAudio Member
 
Join Date: Apr 2012
Location: Grand Blanc, MI
Quote:
Originally Posted by OzzieAudio View Post
Hi Cristi, I've received my four CxD300-8R modules and my two smps500r power supplies - thanks. I plan to install two modules and one power supply in each of my active speakers. Do you recommend putting the electronics in a metal enclosure or can I just bolt them all to one of the wooden inside walls of each speaker?
I have about the same question. I'm not going to put the amp in a speaker, but in a wooden box. Is a metal shell required?

(have a SMPS800RE and a ta3020 kit in the mail, if that makes a difference.)

Thank you.
Duane
 
Old 6th November 2012, 06:57 PM   #166
diyAudio Member
 
Join Date: Dec 2008
Location: Hong Kong or Europe
Dear fellows, I couldn't access the forum for more than one week. some major event will take part over here this week and next week and I thing it has to do with connection problems.

The modules can be installed in the speaker enclosure if there is enough airflow from the speakers to prevent overheating, and keep the heatsinks at a reasonably low temperature, below 75-80*C where the OT protection will trigger.
__________________
www.connexelectronic.com complete assembled amplifier and SMPS
 
Old 9th November 2012, 09:48 AM   #167
diyAudio Member
 
Join Date: Apr 2004
Location: Gold Coast, Australia
Thanks Cristi,
Would a metal enclosure provide any useful screening from spurious signals or be beneficial for grounding purposes?
__________________
Now working on a budget Line Array.
 
Old 12th November 2012, 03:18 PM   #168
diyAudio Member
 
Join Date: Dec 2008
Location: Hong Kong or Europe
In some cases yes. but mostly doesn't have any significant positive effect, especially if the modules are correctly wired and their position and distance is correct. basically the power supply must be installed such as the transformer to be furthers from the small signal stages and wires. also, the GND loops must be avoided and the signal wires must not be routed close or togheter with power wires, speaker output wires and any other wires.
__________________
www.connexelectronic.com complete assembled amplifier and SMPS
 
Old 19th November 2012, 07:35 PM   #169
Ryssen is offline Ryssen  Sweden
diyAudio Member
 
Ryssen's Avatar
 
Join Date: Dec 2003
Location: Sweden--> Here
Hello,can the DA-1 be bridged and drive a 4 ohm speaker?
I have 72v.
What is the size of the amp?
__________________
Regards Åke
 
Old 5th December 2012, 05:32 PM   #170
MBeer is offline MBeer  United Kingdom
diyAudio Member
 
Join Date: Dec 2012
Location: Edinburgh, Scotland
Default CXD400 and IRS2092 module query

I would like some information on the IRS2092 modular amplifier and the CXD400 modules, as I am considering using one or the other in a project. I need a single channel amplifier of 400 to 600 watts into 4 ohms, to use as a power amplifier for bass guitar.
-Do you have sensitivity and input impedance figures for both modules?
-Does the IRS2092 have a balanced or single ended input?
-What are the dimensions of the IRS2092 modular amplifier.
-Which SMPS would you recommend to power a single CXD400 module?
I have emailed you these questions also, but I thought it worth posting them here in case you had problems accessing the email.
 

 


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
non surface mount class D mono audio power amplifiers Conor Digital Source 10 4th October 2013 07:38 PM
Single-Ended Class-A Audio Amplifiers shaan Everything Else 32 4th September 2009 02:42 AM
pro amplifiers vs. home audio amplifiers bonsai171 Solid State 26 25th February 2004 08:24 PM
Class A vs. IC amplifiers for PC audio Beggar Solid State 15 26th July 2002 11:58 AM


New To Site? Need Help?

All times are GMT. The time now is 03:48 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2015 DragonByte Technologies Ltd.
Copyright ©1999-2015 diyAudio

Content Relevant URLs by vBSEO 3.3.2