Class-T Integrated Amp? - diyAudio
Go Back   Home > Forums > Amplifiers > Class D

Class D Switching Power Amplifiers and Power D/A conversion

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 18th September 2002, 02:23 PM   #1
diyAudio Member
 
Join Date: May 2002
Location: Cincinnati, OH now Columbus,OH USA
Send a message via AIM to BeanZ
Default Class-T Integrated Amp?

I recently designed and built a custom four channel Class-T integrated amplifier based on a pair of TA0102A drivers from Tripath for a Senior Design Project. The system incorporated a four channel preamp with bass, midrange, treble, volume, and balance for each pair of channels. Each pair of channels are bridgeable from a switch on the front panel and another switch allows for user selectable mute. Overcurrent and overvoltage protection. Each channel has 190WRMS into 4ohms and about 90WRMS into 8ohms. The system can bridge to over 300WRMS per channel. The power supply is scalable an can be changed to accomodate higher voltage rails and a different series of drivers. The power supply starts with an offline active power factor correction circuit which switches an output voltage up to 400VDC while maintaining a AC line power factor of no less than 0.99 under all conditions. The 400VDC bus is fed into a Zero-Voltage Switching power supply with average current-mode control. The ZVS converter is a resonant power supply topology which is very similar to the full-bridge except for without the disadvantages. The ZVS switches the transistors when the voltage across them is zero volts and thus eliminating any switching noise. The only disadvantage to this converter is obtaining zero voltage switching over a large load range. The bottom line is: The system weighs less than 8 pounds and fits inside a chassis which is less than 1/3 of a cubic ft. I am thinking about starting a web page highlighting the beginning to end build of one of these units. There are custom double-sided circuit boards with silkscreen and solder mask, custom magnetics design, thermal design, and switching design. It may be able to teach some good stuff to some who have never designed in this arena before. I am just trying to see what the interest in this project would be and if there is an interest I have two units that can be built. There were six total (4 were sold). Let me know if there is any interest to follow this project and I will post some project pages.
Here is a picture of a prototype system outside of the case and with informal wiring.

BeanZ
__________________
BeanZ
  Reply With Quote
Old 18th September 2002, 02:54 PM   #2
e96mlo is offline e96mlo  Sweden
diyAudio Member
 
Join Date: Apr 2002
Location: Helsingborg, Sweden
I would like to read more about your project! I'm working on my master theisis and will be designing a ZVS PSU in the near future.

By the way, where is the picture you mensioned?

/Marcus
  Reply With Quote
Old 18th September 2002, 02:59 PM   #3
diyAudio Member
 
Join Date: May 2002
Location: Cincinnati, OH now Columbus,OH USA
Send a message via AIM to BeanZ
The picture was too big to load onto the site. It is available for email upon request. The power supply is based upon the UC3875 phase-shifted controller, completely isolated feedback and MOSFET gate drive. The PFC is based upon the UC3854

BeanZ
__________________
BeanZ
  Reply With Quote
Old 24th January 2003, 04:12 PM   #4
diyAudio Member
 
Join Date: May 2002
Location: Cincinnati, OH now Columbus,OH USA
Send a message via AIM to BeanZ
I have received a lot of interest in this project over the last few months and a bunch more just recently. I will soon make available some of the design details. If one attempts to work with the switching power supply as will be described in the next few weeks, keep in mind that there exists potentiall Lethal voltages in excess of 400VDC with many joules of energy behind it. Also keep in mind that the entire PFC circuit is entirely a mains circuit which means that the circuit is not isolated and is referenced to the neutral of the AC line...an isolated channel o-scope should be used or run two channels differentially. If an isolated channel scope is not used, then the circuit will be referenced to earth an will explode. The amplifier is based on the TA0102A driver modules which are now discontinued and difficult to get. However, the pin out is the same of the TA0104 and TA0105 modules and with minimal changes to components selection the same board can be used. I will present the design as a gradual design and build of such and amplifier and power supply. Keep in touch for the upcoming saga!!!!

BeanZ
__________________
BeanZ
  Reply With Quote
Old 4th April 2004, 09:09 PM   #5
diyAudio Member
 
Join Date: May 2002
Location: Cincinnati, OH now Columbus,OH USA
Send a message via AIM to BeanZ
That last post was submitted over a year ago but finally I am going to sit down and share this design with our community. Again this design is an integrated four channel Class-T based audio amplifier. The features include:

--1000W Active Power Factor Correction Circuit
--Zero-Voltage Switching Power Supply
--Four Channel 190WRMS x 4 @ 4ohms
--Simple pre-amplifier with bass, treble, midrange, balance,
volume control for each stereo pair.
--Over voltage, short-circuit protection

The project includes printed circuit boards and a chassis. Stay tuned for pictures and details of the contruction.

Here is the fundamentals for anyone who want to do any pre-research......

PFC is based on the TI UC3854 Power Factor Controller
ZVS is based on the TI UC3875 Phase Shift Resonant Controller
Amplifiers based on the Tripath TA0102A modules.

Feel free to send emails directly to me or post any questions and I will try my best to answer them. I have some extra boards and parts that will be available if anyone is interested.

BeanZ
__________________
BeanZ
  Reply With Quote
Old 4th April 2004, 09:11 PM   #6
jleaman is offline jleaman  Belgium
Banned
 
Join Date: Apr 2002
Send a message via AIM to jleaman
can i see the picture.. if you send to me ill resize it for you and also post it here on the diy..


jkmierau @ curtek . com

J'
  Reply With Quote
Old 4th April 2004, 09:15 PM   #7
diyAudio Member
 
Join Date: May 2002
Location: Cincinnati, OH now Columbus,OH USA
Send a message via AIM to BeanZ
I have a digital camera now and I will have no problems posting photos on here. Stay tuned.
__________________
BeanZ
  Reply With Quote
Old 16th April 2004, 08:37 AM   #8
wytco0 is offline wytco0  United Kingdom
diyAudio Member
 
Join Date: Apr 2004
Location: Hastings
BeanZ,
Do you have the pictures of this project?


All,
I am very interested in the tripath eval boards. I have searched here and elswhere to find DIY amps using these boards and found very little. I read the review of the Veritas P400 amp a couple of years ago which commented that it was a fine amp. It seem that it should be possible to build a very high performace amp using tripath boards for a failrly small amount of cash ! I am sure there must be a reason why this isnt being done?

Any pointers to amps built with these boards or info about them and why they dont seem very popular would be appreciated.

Thanks.
  Reply With Quote
Old 17th April 2004, 07:02 AM   #9
diyAudio Member
 
Join Date: Jan 2001
I considered getting the eval boards years ago, but there was some doubt regarding HF noise. Have you done any tests? Freq/Pulse response. Ripple Voltage. THD etc?
And above all, how does it sound?
  Reply With Quote
Old 17th April 2004, 12:01 PM   #10
diyAudio Member
 
Join Date: Dec 2003
Location: Mumbai
hi

i have gone over the entire tripath cd information kit sent to me by a friend

at my end i have made mosfets , msofets and more mosfets

i would like pricing info

as

as of now to me irf s 150 ets r the best , powerful , high spls clean and have very high degree of critical application properties + are rock soilid

i have had lots of experince in pro audio and serious sound reinforcement

one of the products that have 9i have always admired is meyer s

and meyers uses IRF 150 s , if you hear a meyer (thats an IRF playing)

though i dont want to undermine tripaths research and products or their quality , i really need to compare the price ing

and a justifiable price reduction thru saving on the power supply in tripath applications compaired to the price of the modules pcb s ets

another thing i would like to point out is to the availability of the tripath modules should a company use them - will a service engineer have access to spare modules (world - wide)

and how many service engineer will be familar with this stuff - unless aggressive marketing is done and tech info is published in electronics magazines ets

as for the IRF s they are 65 cents each here in india from Harris tech


suranjan

transducer design engineer
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Class 'A' Integrated Cd Player..? stuartbooth Everything Else 7 14th November 2008 07:20 AM
FS: 41hz Amp6 Class D Integrated Amplifier mrdon Swap Meet 2 31st July 2006 02:02 PM
Class A tube integrated circuit request ckwong99 Tubes / Valves 8 4th August 2005 05:14 AM
Class A 45 watts integrated lpd Swap Meet 1 28th November 2004 12:23 PM


New To Site? Need Help?

All times are GMT. The time now is 05:31 PM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2