My class D amp

opor · 2013-09-17 8:21 pm

Hi Manoj,
What happen with my amp,AUD900? It can not run at fully level. Capacitor 0.47uf at LC filter is burned. I am using BD139s,140s as totem. 2 pairs of IRFP4232 as output fets. TIP31 with 13vzener as bias power.

Regards,
Opor

manojtm · 2013-09-18 9:28 am

Hi Manoj,
What happen with my amp,AUD900? It can not run at fully level. Capacitor 0.47uf at LC filter is burned. I am using BD139s,140s as totem. 2 pairs of IRFP4232 as output fets. TIP31 with 13vzener as bias power.

Hi OPOR,

use 474/400V for +/-85V supply and 474/600V for +/-140V supply(ie:: 4 times higher)

Regards
MANOJ

aman khalsa · 2013-09-19 5:04 am

Can any 1pls share aud900 pcb pls ......

Regards

manojtm · 2013-10-05 6:45 am

Hi,

PCB ready for AUD1000SD

Regards
MANOJ

manojtm · 2013-10-28 3:32 pm

Hi All,

waiting MMBT5401/5551 SMD,not completed yet.

sorry for the picture quality(mobile camera)

Regards
MANOJ

manojtm · 2013-11-11 11:07 am

Hi All,

3 mistakes found on my PCB after resolved this its working fine.HF clarity so good compare to my single side design(fsw=250KHz). EMI is very less.No noise

attaching my Volume limiter with clip and sig indicator PCB

Regards
MANOJ

ravpreet420 · 2013-11-11 11:55 am

nice work sir........

andrewlebon · 2013-11-15 5:55 am

Hi Manoj
greetings which is your best AUD amp i want to try it feeling bored
warm regards
andrew lebon

manojtm · 2013-11-16 3:29 pm

Hi andrew,

AUD1000SD dual side board is better

I use FDP075N15A_F102 MOSFET with +/-68V supply (max +/-72V)and 22uH coil (T157-2)

Regards
MANOJ

manojtm · 2013-11-16 3:54 pm

Hi,

AUD1000SD working pic..

Regards
MANOJ

manojtm · 2013-11-16 4:30 pm

Hi,

ASE(Aud Sound Enhancer) for AUD1000SD

Regards
MANOJ

PetruV · 2013-11-16 6:38 pm

What does it do???

manojtm · 2013-11-17 12:37 pm

What does it do???

Hi,
its improve sound quality

Regards
MANOJ

andrewlebon · 2013-11-17 1:55 pm

dual side pcb

AUD1000SD dual side board is better
IRS1500 Dual side pcb stereo

warm regards
andrew lebon

andrewlebon · 2013-11-17 2:00 pm

dual side pcb

AUD1000SD dual side board is better
IRS1500 Dual side pcb stereo

warm regards
andrew lebon

manojtm · 2013-11-18 3:55 pm

Hi Andrew,

AUD1000SD

Balanced IN
Volume Control
Protection:
DC Protect using relay(20A,5mS,2.7V sense)
Over Current +&- Rails
Thermal switch NC type
SUPPLY
35A Bridge Diode
2X 10000uF/80V
and Bias Supply

Only we need 50V-0V-50V AC 10A & 0V-12V AC 1A Transformer.

we can easily add limiter for AUD1000SD

Regards
MANOJ

Deleted member 148505 · 2013-11-22 1:37 am

Congrats Manoj! That looks very good...

manojtm · 2013-11-25 8:37 am

Congrats Manoj! That looks very good...

Hi Jlester,

Thank you for the comment.

I am using 150V 130A MOSFET (MAx Supply Rail +/-72V)

For 2R Load OC sense 1K5 resistor to change For 34A

Now My AUD1000SD OC is 28.7A
Supply Rail +/-72V
Supply Rail for Max. Volume +/-68.6V
FTC RMS @4R 1176W
OC for 4R Load is 17A If i use 2R Load @MID Volume no problem increase this level OC active and it will trip
I check all levels like short SP line,max Volume point on 2Hr. and remove earth wire on signal input @ max volume point,touch TL071 osc point...etc My MOSFET is survive no issues, No heat
It is Better for All

Regards
MANOJ

manojtm · 2013-12-24 7:45 am

Hi All,

WISH U ALL MERRY X'MAS

Regards
MANOJ

sandeep kayarkar · 2014-01-30 10:42 am

My AUD600

Just waiting for some parts

My class D amp

Member

Member

Member

Member

Attachments

Member

Attachments

Member

Attachments

Member

R.I.P.

Member

Member

Attachments

Member

Attachments

Member

Member

R.I.P.

Attachments

R.I.P.

Attachments

Member

Deleted member 148505

Member

Member

Member

Attachments