Hi all.
A Powersoft K8 came in for repair due to water damage.
Upon repairing a track on the underside of the pcb, i also found
a bad voltage regulator.
Unfortunately it is cracked open and i am not able to see which one is it.
I am referring to U4 in the power amplifier section.
Here is a pic that might help.
A Powersoft K8 came in for repair due to water damage.
Upon repairing a track on the underside of the pcb, i also found
a bad voltage regulator.
Unfortunately it is cracked open and i am not able to see which one is it.
I am referring to U4 in the power amplifier section.
Here is a pic that might help.
Attachments
You'll probably have thought of this, but is there an identical regulator doing the same job on the other channel?
I suppose looking at the voltage ratings of connected caps on the output would give you a ballpark idea of the o/p voltage.
I understand that powersoft are a bit cagey with their service data, unfortunately.
I suppose looking at the voltage ratings of connected caps on the output would give you a ballpark idea of the o/p voltage.
I understand that powersoft are a bit cagey with their service data, unfortunately.
Can you please make for me some GOOD QUALITY pictures of entire amplifier, divided in sections, from UP, so I can observe better what they do there?
Interesed to see inductor coils, output filters, storage capacitors, etc
Please sent on my email: claudiu971@yahoo.com
Thank you and good luck in repair!
Interesed to see inductor coils, output filters, storage capacitors, etc
Please sent on my email: claudiu971@yahoo.com
Thank you and good luck in repair!
hi all..!!
any have schematic powersoft 5000/7000..?
i have trouble with this device.
thank's for all member..!
please send for file to my mail.
joerudi1976@gmail.com
any have schematic powersoft 5000/7000..?
i have trouble with this device.
thank's for all member..!
please send for file to my mail.
joerudi1976@gmail.com
Powersoft Digam 5000-7000
hi,
any have schematic powersoft 5000/7000..?
thanks a lot
mail: rivulet@volny.cz
hi,
any have schematic powersoft 5000/7000..?
thanks a lot
mail: rivulet@volny.cz
hi all,
any have schematic powersoft 5000/7000..?
please send for file to my mail.
marstangelenadam@gmail.com
please send for file to my mail.
thanxs.
any have schematic powersoft 5000/7000..?
please send for file to my mail.
marstangelenadam@gmail.com
please send for file to my mail.
thanxs.
Can anyone help with quality pictures to see k-cntrl component side. Both side of kfrnt the display and buttons. The top card board and components. I'm also struggling with the kalsu for PSU. I also need clear picture s of both side to see tracks connections. Please email me at mgee626@gmail.com
Thanks you guys
Thanks you guys
+/-175v remember there's step up to upgrade k series
+/- 175V very high with huge switching losses in IDLE
Amp perfect for bass
But High Voltage Mosfet will be slow with high rise and fall times
clarity will decrease in Mid and High
I like to know switching Frequency ?
I think something between 200 - 250 khz.
Does somebody want have schematic from K series ?
Last edited:
I believe at least some powersoft amplifiers use variable rail voltage:
R&D Stories: Future Shock. Powersoft Audio’s Amplifier Technologies | audioXpress
so even if your measuring +/-175 this might be reduced before the output transistors?
would be interesting to see a schematic.
R&D Stories: Future Shock. Powersoft Audio’s Amplifier Technologies | audioXpress
so even if your measuring +/-175 this might be reduced before the output transistors?
would be interesting to see a schematic.
- Status
- This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button.
- Home
- Amplifiers
- Class D
- Powersoft K8