Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Class D Switching Power Amplifiers and Power D/A conversion

best compromise for LC filter design, driving 4, 6 and 8 ohm loads
best compromise for LC filter design, driving 4, 6 and 8 ohm loads
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Thread Tools Search this Thread
Old 6th March 2011, 06:33 PM   #1
Oil is offline Oil  United Kingdom
diyAudio Member
Join Date: Aug 2004
Location: UK
Default best compromise for LC filter design, driving 4, 6 and 8 ohm loads

Hi All

I'm currently in the process of designing a small amp based on a TI TPA3106.

I'd like to have the output filter designed so that it will run 4, 6 and 8 ohm loads satisfactorily, without excessive peaking / THD implications (as little as possible anyway)

I have read through this: http://focus.ti.com/lit/an/sloa119a/sloa119a.pdf and it seems as though the tables on pages 11 and 12 show 15-20 uH with 1.5-2 uF would be a reasonable place to start.

I'm hoping that somebody can offer some suggestions on the values to use?

Given that I don't have the equipment to measure the actual results, could anybody recommend a suitable software package to simulate the filter design and implications?

Lastly, I see sure electronics put a 470uF coupling electrolytic after the filter on their TPA3123 board: here (page 15) (they use a 33uH / 1.47uF combination). What is the benefit to doing this and how would you guess they justified the filter selection?

Many thanks


Last edited by Oil; 6th March 2011 at 06:46 PM.
  Reply With Quote
Old 6th March 2011, 07:07 PM   #2
theAnonymous1 is offline theAnonymous1  United States
diyAudio Member
theAnonymous1's Avatar
Join Date: Feb 2004
Location: Anonymityville
The Sure TPA3123 board uses 470uF caps on the output to block the DC bias since it is a single-ended design running off a single supply. The TPA3106 runs BTL so these caps are not needed.

Here is an online filter calculator page you can mess around with....

Filter Design and Analysis

On my TPA3106D1 boards I use 15uH + 1uF. I haven't measured the response, but it sounds fine to my ears running 4-8R loads.
  Reply With Quote
Old 7th March 2011, 01:36 AM   #3
nigelwright7557 is offline nigelwright7557  United Kingdom
diyAudio Member
nigelwright7557's Avatar
Join Date: Apr 2008
Location: Carlisle, England
Just make sure the inductor will take the current for the 4 ohm setup OK.

My class d amp uses 22uh and 470nf and runs into 4 ohms very well.
PCBCAD51 pcb design software. 2018 version out now. http://www.murtonpikesystems.co.uk
  Reply With Quote
Old 7th March 2011, 05:12 AM   #4
killerbobjr is offline killerbobjr  United States
diyAudio Member
Join Date: Sep 2004
Location: killer
You can design for a nominal impedance of 4 ohms and use a Zobel network to minimize impedance mismatches. If you design the output filter for an Fco of around 1/5 the switching frequency (typically around 250KHz for the TI TPAxxx chips), you can pretty much get away with using LC values for a 4 ohm load and not have an audible HF peak when attaching 8 ohm loads.
  Reply With Quote


best compromise for LC filter design, driving 4, 6 and 8 ohm loadsHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Amplifier Design for Fractional Ohm Loads SlunkBoy Solid State 3 9th February 2010 08:01 PM
Driving Low Impedance Loads weinstro Solid State 14 8th May 2005 10:53 PM
LC filter design demons_wing Solid State 5 2nd July 2004 04:06 AM
Gainclone driving inductive loads diyman Chip Amps 1 12th April 2004 10:53 AM
Zen driving high impedance loads supa-roo Pass Labs 2 18th April 2003 08:23 PM

New To Site? Need Help?

All times are GMT. The time now is 05:16 PM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.79%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright ©1999-2017 diyAudio