...
like this
Hi Thienchay.
The PCB IRS200D correct?
It worked perfectly?
I am needing to mount two of these plates.
Thank you for your attention.
IRS-1500 Fail !
Hi guys..
so I've just finished IRS1500..but there is also a problem
please watch this video :
Class-D IRSD1K5 - No & Low Level input Problem - YouTube
when i turn on power supply..after s short delay , speaker connected to amp's out. as you can hear in video , there is a noise available at output. (input volume = 0) and when i increase volume up to 4~5%, a really bad audio signal become appear. also the active led indicator isn't bright constantly.
when i increase the volume (about 7~8 %) the amp start to oscillate and those problem solved.
guys please help me. anyone have similar problems ?
Regards,
IRSound
Hi guys..
so I've just finished IRS1500..but there is also a problem
please watch this video :
Class-D IRSD1K5 - No & Low Level input Problem - YouTube
when i turn on power supply..after s short delay , speaker connected to amp's out. as you can hear in video , there is a noise available at output. (input volume = 0) and when i increase volume up to 4~5%, a really bad audio signal become appear. also the active led indicator isn't bright constantly.
when i increase the volume (about 7~8 %) the amp start to oscillate and those problem solved.
guys please help me. anyone have similar problems ?
Regards,
IRSound
Hi guys..
so I've just finished IRS1500..but there is also a problem
please watch this video :
Class-D IRSD1K5 - No & Low Level input Problem - YouTube
when i turn on power supply..after s short delay , speaker connected to amp's out. as you can hear in video , there is a noise available at output. (input volume = 0) and when i increase volume up to 4~5%, a really bad audio signal become appear. also the active led indicator isn't bright constantly.
when i increase the volume (about 7~8 %) the amp start to oscillate and those problem solved.
guys please help me. anyone have similar problems ?
Regards,
IRSound
post pcb picture in high definition to see what his mistake was.
Hi Jcoelhogsia,
Thanks for helping me..
this list shows the difference between my component and attached layout :
- Using BYV28-600 instead of MUR160 (beside IR2110)
- Using MUR460 instead of MUR160 after inductor
- Using 1N5819 instead of 4148 (mosfet's gate)
- Using IRFP250N instead of FDA69N25
- Using 47.5 Ohm gate resistor
and i have problem with no input signal and lower level input , like what you see in that video.
Regards,
IRSound
Thanks for helping me..
this list shows the difference between my component and attached layout :
- Using BYV28-600 instead of MUR160 (beside IR2110)
- Using MUR460 instead of MUR160 after inductor
- Using 1N5819 instead of 4148 (mosfet's gate)
- Using IRFP250N instead of FDA69N25
- Using 47.5 Ohm gate resistor
and i have problem with no input signal and lower level input , like what you see in that video.
Regards,
IRSound
Attachments
Last edited:
Hi Jcoelhogsia,
Thanks for helping me..
this list shows the difference between my component and attached layout :
- Using BYV28-600 instead of MUR160 (beside IR2110)
- Using MUR460 instead of MUR160 after inductor
- Using 1N5819 instead of 4148 (mosfet's gate)
- Using IRFP250N instead of FDA69N25
- Using 47.5 Ohm gate resistor
and i have problem with no input signal and lower level input , like what you see in that video.
Regards,
IRSound
post the other side of the pcb.
ok...
do you have any suggestion ?
pcb ok, its assembly this perfect, as you have to replace the diode mur160, what voltage are you using? My run this perfect./http://www.youtube.com/watch?v=HU4e88xkp_M
Last edited:
ja gave defect in assembling yes!
trails off!
Input Signal short!
led oscillating!
Power supply + 68 -68!
+ -12/14 Volt bias!
I did not modify the components!
the name of the song and not know a mix!
Hi,Now I'm making this pcb .It is like 80% done.
I have to check the gnd returns
Ty luka, I´m working on it.
I want to know which software you use for making pcb?
Regards,
Pravpa
jcoelhogsia,
please test you amp with this step and tell me the result :
1-connect input , output and all supply voltages connections.
2-apply mains to transformer (+/- 68V)
3-now , apply bias voltage to amp
4-watch active LED status (tell me)
5-now , play sound with lowest volume and see the result. then increase volume and see the result.keep me posted.
Regards
please test you amp with this step and tell me the result :
1-connect input , output and all supply voltages connections.
2-apply mains to transformer (+/- 68V)
3-now , apply bias voltage to amp
4-watch active LED status (tell me)
5-now , play sound with lowest volume and see the result. then increase volume and see the result.keep me posted.
Regards
These days I am very busy with my work. So I'll test is available and inform you.
As for the name of the song you asked.
Music: LEMONADE, singer: ALEXANDRA STAN
AUD600 with sub crossover
http://www.diyaudio.com/forums/class-d/226812-my-class-d-amp-7.html
Regards,
Pravpa
Hi,
http://www.diyaudio.com/forums/class-d/226812-my-class-d-amp-7.html
Regards,
Pravpa
Hi to all
who have order assembled Class D pcb from Detex audio website already and received ?
have order and pay but no luck up today, another friend from DIY have same problem
Last edited:
Hello Everybody:
is this core suitable for class D amp? any other suggestions?
T157-2 Micrometals Iron Powder Toroid
Thanks
Raj
is this core suitable for class D amp? any other suggestions?
T157-2 Micrometals Iron Powder Toroid
Thanks
Raj
