UCD 25 watts to 1200 watts using 2 mosfets

[sweetperfume]

ir2110 with totem bjt and tc4220

irvynejay sir,
can u plz give the pcb file of circuit with totem pole using bd transistors

 

[irvynejay]

andrewlebon has the layout of BD type pls ask him

 

[sweetperfume]

andrewlebon has the layout of BD type pls ask him

thank u sir...i'll drop a msg for him

 

[sweetperfume]

Try FAN7392 instead of IR2110 ic seems sound is more refined
warm regards
andrew lebon

sir andrewlebon can u send me the pcb file of the circuit with bd totem pole for driving three pairs......i asked irvynejay sir he told me to ask u for that...so plz send me the file sir.....
warm regards

 

[exflaco]

Srs this and open diy forum pcb and schem for all please no godd idea share betwen menbers

 

[apexaudio]

Hey sir Aper i work very hard on your Friendly DIY apex D500 ,never work ,yours clas AB and H very respeted in DIY forum ,y dont undestand because ,share bad schem and boards not tested , realy a joke ,Diyaudio the best.......

Post pictures and measurements of your Apex D500 and I can help you.
Regards

 

[andrewlebon]

totem with bd 139 140

Hi Nano
greetings do you have this file to make
warm regards
andrew lebon

 

[NANOTECNOLOGIA]

Hi Nano
greetings do you have this file to make
warm regards
andrew lebon

have your email

 

[exflaco]

Andrew ,Nano share to me please

 

[kirubakaran]

Hi.. pls help to fix the problem i will try irs900 and amplificador 1200 schematic with irfp250 ir2110 get warm and smoke logic supply 5v rail voltage +-60 V pls guide me to how fix this problem

 

[exflaco]

Could share original Sprint Layout files,tanks

 

[paskal9]

Hi.. pls help to fix the problem i will try irs900 and amplificador 1200 schematic with irfp250 ir2110 get warm and smoke logic supply 5v rail voltage +-60 V pls guide me to how fix this problem

which design that you're using? irs900 or amplificador 1200?

if this if your first project, it would be best if you could try with a lower, say 35 or 45v first before moving to >50v. my amp which is dead stable at 35v went up in smoke when i feed it 65v. make a stable amp at lower voltage first before going higher.

 

[kirubakaran]

i will try both desing problem same

which design that you're using? irs900 or amplificador 1200?

if this if your first project, it would be best if you could try with a lower, say 35 or 45v first before moving to >50v. my amp which is dead stable at 35v went up in smoke when i feed it 65v. make a stable amp at lower voltage first before going higher.

i will try both desing, problem are same. +/- 30v amp ok. but i feed above 40v gate driver get warm or smoke. pls help to solve.

 

[kirubakaran]

iraudio class d amp model with ir2011

iraudio amp class d amp model with ir2011 found on internet. ir2011 is not available in my location can i change ir2011 to ir2110 any difference between gate driver?

 

[andrewlebon]

Hi Kirubakaran
greetings what core are you using
warm regards
andrew lebon

 

[manojtm]

Hi andrew,

EDT29 with 1mm Gap (70uH) coil was tested, Better sound compare to my Drum core
only EMI is little high compare to Drum Core,cool

regards
MANOJ

 

[don2007ksa]

IRS DUAL OUTPUT

hello kirubakaran,IR2110 is a 14pin package while IR2011 is an 8pin you cannot insert it write away with out interchanging the pin's,one more thing it will take your time,try this layout i'll try to upload,hope it will help.

 

[kirubakaran]

Hi Kirubakaran
greetings what core are you using
warm regards
andrew lebon

Hi... andrewlebon greetings i use iron ferrite t130/6 yellow ring core 22uh

 

[kirubakaran]

hello kirubakaran,IR2110 is a 14pin package while IR2011 is an 8pin you cannot insert it write away with out interchanging the pin's,one more thing it will take your time,try this layout i'll try to upload,hope it will help.

hi... don thank you. are you try this?

 

[kirubakaran]

Hi... andrewlebon greetings i use iron ferrite t130/6 yellow ring core 22uh

Hi... andrewlebon
irs2092 is available in india if available what is cost each in indian currency? pls give me details thanks in advance.