Do I need a resistor if Im going directly from rca...

bundee1 · 05:54 AM

inputs to the amp board of the teac al700p? Im trying to piece together some kind of record of the mods done to this amp. With a lot of help from Puffin (thanks, bro!) Im updating my Apple Lossless library to run Squeezebox from my Netbook and an external drive and listen to this amp. Should be a pretty green setup. The netbook at full load consumes 17w, the Teac 45w, and I think the Squeezebox draws 10 watts. My preamp is a battery powered Bottlehead Quickie. So far so good but I want to finish modding this Teac and Ive been taking pictures of my mods to help someone later on.

Ill post a drawing of the board with the parts identified tomorrow.

I would appreciate your help in answering my questions so I can fill in the gaps of my mod knowledge. Thanks again Puffin and to anyone else who can contribute.

bundee1 · 6th April 2010, 01:05 AM

Here's the schematic and I know enough to see the pertinent info is on page 2 but I dont know how to connect the parts and if they are all necessary if Im going straight from the RCA inputs to the amp board.

A-L700P_SCHEMATIC[1].pdf

I already have the 2.2 caps replaced on the board now where do the two resistors go and what values are they?

2nd April 2010, 05:38 AM	#1
bundee1 diyAudio Member Join Date: May 2005 Location: Shea Stadium	Do I need a resistor if Im going directly from rca... inputs to the amp board of the teac al700p? Im trying to piece together some kind of record of the mods done to this amp. With a lot of help from Puffin (thanks, bro!) Im updating my Apple Lossless library to run Squeezebox from my Netbook and an external drive and listen to this amp. Should be a pretty green setup. The netbook at full load consumes 17w, the Teac 45w, and I think the Squeezebox draws 10 watts. My preamp is a battery powered Bottlehead Quickie. So far so good but I want to finish modding this Teac and Ive been taking pictures of my mods to help someone later on. Ill post a drawing of the board with the parts identified tomorrow. I would appreciate your help in answering my questions so I can fill in the gaps of my mod knowledge. Thanks again Puffin and to anyone else who can contribute. Last edited by bundee1; 2nd April 2010 at 05:54 AM.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
WTB : RCA MI-1428B or RCA Mi-1443 drivers wanted	hum4god	Swap Meet	0	3rd March 2010 01:30 AM
WTB: 1 m well made high end interconnects rca rca pair thanks	spwal	Swap Meet	1	18th February 2007 02:31 PM
screen-plate resistor and grid leak resistor	metebalci	Tubes / Valves	4	26th February 2004 03:18 AM
Hi, im new to DIY audio, im wanting to buy the audax HT kit and have a few questions	undertoe	Multi-Way	13	23rd January 2003 07:12 AM

New To Site?	Need Help?
Register to Participate Search Privacy Statement Contact Us	Frequently Asked Questions Did you forget your password? Mark Forums Read


	Please consider donating to help us continue to serve you. Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving

6th April 2010, 01:05 AM	#2
bundee1 diyAudio Member Join Date: May 2005 Location: Shea Stadium	Here's the schematic and I know enough to see the pertinent info is on page 2 but I dont know how to connect the parts and if they are all necessary if Im going straight from the RCA inputs to the amp board. A-L700P_SCHEMATIC[1].pdf I already have the 2.2 caps replaced on the board now where do the two resistors go and what values are they?

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)