trouble with IR2011 2110 spice subckt

thierry38efd · 22nd December 2009, 05:03 PM

hello.

trying to simulate a discrete D amp with LTspice,i've found some model of IR2011 and IR2110.

these two models need to be tie at ground in simulation,but in reality to -Vcc.

so it's impossible to make the simulation working.

i've try to connect the chip in different way,but nothing get a normal behaviour.

the only way is to use IR2011 and IR2110 connect to ground in LTspice but modulator with level shifting cannot be insert in the schematic...

maybe someone knows a way to make it working ?

thierry38efd · 22nd December 2009, 06:10 PM

too late now...

IR2011.sub is working perfectly,even with 1nS step simulation.
thanks to analogspice to make this model

still problem with IR2110 from IR (it's working with ground as reference)

but chip are similar (except prop time...).

simulation looks a good base to design D amp (UCD like).

any feedback for use IR2110 in LTspice ?

thierry38efd · 29th December 2009, 11:03 PM

the LTspice schematic

UCD like with IR2011

thierry38efd · 05:36 PM

some of FFT

i've start to design a double side PCB,still checking for a good topology,this is in a good way...
500 VA 2x30 V ac ,double slow rectifier bridge ,irf540n output mosfet at first try.

comparator will be lm360,op amp ne5532 and IR2110 as mos driver

22nd December 2009, 05:03 PM	#1
thierry38efd diyAudio Member Join Date: Jan 2006 Location: grenoble	trouble with IR2011 2110 spice subckt hello. trying to simulate a discrete D amp with LTspice,i've found some model of IR2011 and IR2110. these two models need to be tie at ground in simulation,but in reality to -Vcc. so it's impossible to make the simulation working. i've try to connect the chip in different way,but nothing get a normal behaviour. the only way is to use IR2011 and IR2110 connect to ground in LTspice but modulator with level shifting cannot be insert in the schematic... maybe someone knows a way to make it working ?

30th December 2009, 05:07 PM	#4
thierry38efd diyAudio Member Join Date: Jan 2006 Location: grenoble	some of FFT i've start to design a double side PCB,still checking for a good topology,this is in a good way... 500 VA 2x30 V ac ,double slow rectifier bridge ,irf540n output mosfet at first try. comparator will be lm360,op amp ne5532 and IR2110 as mos driver Last edited by thierry38efd; 30th December 2009 at 05:36 PM.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Marantz 2110 Scope Issue	pezza89	Solid State	6	31st May 2012 04:16 PM
IR2011 Gate Driver	smartsabby	Class D	1	27th February 2008 04:20 AM
crate vc 2110 schematic ???	vlljpior	Tubes / Valves	1	10th October 2006 08:40 PM
Wiring the IR2011 Correctly	niroshans	Class D	4	9th April 2006 09:00 PM
dv/dt turn on with ir2011 simulation	oldroborg	Class D	5	20th December 2005 07:39 PM

New To Site?	Need Help?
Register to Participate Search Privacy Statement Contact Us	Frequently Asked Questions Did you forget your password? Mark Forums Read


	Please consider donating to help us continue to serve you. Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving

22nd December 2009, 06:10 PM	#2
thierry38efd diyAudio Member Join Date: Jan 2006 Location: grenoble	too late now... IR2011.sub is working perfectly,even with 1nS step simulation. thanks to analogspice to make this model still problem with IR2110 from IR (it's working with ground as reference) but chip are similar (except prop time...). simulation looks a good base to design D amp (UCD like). any feedback for use IR2110 in LTspice ?