UcD 400 Project

tosehee · 21st September 2009, 07:34 PM

Hello.

Totally new to this amp or DIY in general, and I am hoping to get some helpful guidelines as I never done any type of DIY in the past.

First, here is a spec for my speaker. Speaker is Monitor Audio GR60.

Nominal Power 200 Watt RMS
Peak Power Handling 400 Watt
Frequency Reponse 28 Hz - 30000 kHz
Sensitivity 90 dB
Impedance 6 ohm

What I'd like to build ultimately is.

A. An amp with sufficient to drive my current speaker and have a room for future speaker upgrade.
B. 2 Input. 1 RCA and 1 XLR for balanced with input selector

With the above requirement, here are my questions. If it is answered somewhere, please let me know the links.

1. UcD 400. Is this sufficient or do I need even more poweful amp module?
2. I read that there is no soldering required. Is that a fact or do I need some level of soldering to get this finished?
3. What kind of case can I use? I have a HTPC case that I am not using (desktop look, not the tower). Is that sufficient?
4. What parts do I need to buy for the above requirements?

Thanks in advance for any help and guidelines.

Regards

tinitus · 22nd September 2009, 11:10 PM

Maybe mr Holton heard your prayers
Apparently possible to assemble with no soldering
http://www.aussieamplifiers.com/

tosehee · 23rd September 2009, 12:42 AM

okay. may I can't read..?

i only see the class A/b amps..

21st September 2009, 07:34 PM	#1
tosehee diyAudio Member Join Date: Oct 2008	UcD 400 Project Hello. Totally new to this amp or DIY in general, and I am hoping to get some helpful guidelines as I never done any type of DIY in the past. First, here is a spec for my speaker. Speaker is Monitor Audio GR60. Nominal Power 200 Watt RMS Peak Power Handling 400 Watt Frequency Reponse 28 Hz - 30000 kHz Sensitivity 90 dB Impedance 6 ohm What I'd like to build ultimately is. A. An amp with sufficient to drive my current speaker and have a room for future speaker upgrade. B. 2 Input. 1 RCA and 1 XLR for balanced with input selector With the above requirement, here are my questions. If it is answered somewhere, please let me know the links. 1. UcD 400. Is this sufficient or do I need even more poweful amp module? 2. I read that there is no soldering required. Is that a fact or do I need some level of soldering to get this finished? 3. What kind of case can I use? I have a HTPC case that I am not using (desktop look, not the tower). Is that sufficient? 4. What parts do I need to buy for the above requirements? Thanks in advance for any help and guidelines. Regards

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
CDPRO2 Group Project (open source project)	BrianGT	Digital Source	147	8th August 2008 11:37 AM
My OLD Project....... cheap tube audio project!!!	tube-lover	Tubes / Valves	4	8th May 2008 09:26 PM
Help with first GC project	drproton	Chip Amps	30	21st February 2008 03:46 PM
My first project, cool project.	sorinsistem	Solid State	3	19th January 2006 05:08 PM

New To Site?	Need Help?
Register to Participate Search Privacy Statement Contact Us	Frequently Asked Questions Did you forget your password? Mark Forums Read


	Please consider donating to help us continue to serve you. Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving

22nd September 2009, 11:10 PM	#2
tinitus diyAudio Moderator Join Date: Nov 2005	Maybe mr Holton heard your prayers Apparently possible to assemble with no soldering http://www.aussieamplifiers.com/

23rd September 2009, 12:42 AM	#3
tosehee diyAudio Member Join Date: Oct 2008	okay. may I can't read..? i only see the class A/b amps..

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)