diyAudio

diyAudio (http://www.diyaudio.com/forums/)
-   Class D (http://www.diyaudio.com/forums/class-d/)
-   -   Need service manual or schematics of behringer PMH1000 mixer (http://www.diyaudio.com/forums/class-d/111709-need-service-manual-schematics-behringer-pmh1000-mixer.html)

fredos 10th November 2007 11:19 PM

Need service manual or schematics of behringer PMH1000 mixer
 
I need service manual for a broken ( switching amplifier section and power supply...) PMH1000 powered mixer...Yeah I know it's only a Behringer, but I whant to fix it for a friend...First of all, booth power mosfet and drivers have blow in the power stage (dead short) and this may have blow PFC stage in the power supply. Only the section with TopSwitch work, no power output.

At least, if nobody have it, I will just do an un-powered mixer with it....

Thanks

fredos

oldmaelstrom2 11th November 2007 06:41 AM

here

fredos 11th November 2007 06:04 PM

Thanks a lot! I will fix it, just wish that the HCA4001 is not blow...It's look like a Zetex chip...


Fredos

Eva 11th November 2007 08:35 PM

Thank you very much oldmaelstrom2 for this nice pdf.

If they got the current limiting feature of the PFC to work properly, it should survive dead shorts on the outputs without problem.

SHAME on the way current limiting is implemented in the class D amplifiers, though.

fredos 13th November 2007 12:15 AM

Repaired!

No Eva, I dont think they have done a great job on the protection schem...Power supply blow after dead short on amplifier mosfet...

So the HCA4001 seem to work well. The sound of this crap is like all berhinger crap...Bad! But power amp seem efficient, duty cycle is limited into the HCA4001, so no need to find a way to keep gate charged...Power supply provide +/- 56V, very well regulated..

Some ugly 60Hz noise inside transformer, specialy with 200 watts load and more, but still regulated. Began to drop over 460 watts until 0V with a PAR 64 1000 watts lamp. Did'nt try short, I dont whant to blow it again!

Thanks for serviec manual!

Fredos

fdeck 13th November 2007 12:19 AM

Was I missing something? It did not look like there was any current limiting on the power amp circuit, only the current sense transformer in the power supply. Is this typical of Class-D?

Eva 13th November 2007 12:31 AM

Congratulations ;)

This noise in PFC inductors and transformers is quite usual and is a consequence of sub optimal PFC performance. If you look carefully at the AC current waveform, you will notice discontinuities near zero crossing...

fredos 13th November 2007 12:39 PM

So I will have to increase PFC Choke (330uH)? I whant to fix this, I dont like it!

Fredos

Eva 14th November 2007 02:56 AM

In my PFC designs I got smooth zero crossing by allowing up to 100% duty cycle and by optimizing frequency compensation of the average current control loop. A too *high* PFC inductor value can also produce this behaviour but only for heavy loads. In a finished product the noise is not that easy to fix.

fredos 14th November 2007 04:20 PM

100% duty cycle did not imply short on HV bus under heavy load/low voltage condition????

Fredos


All times are GMT. The time now is 11:15 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio


Content Relevant URLs by vBSEO 3.3.2