The Boominator - another stab at the ultimate party machine

[Kasper Jack]

Originally Posted by jeroendb

Hi guys after lost of reading in This thread I decided devices to build qubinator myself.
Yesterday I orderd my amplifier mk2 by Arjen Helder(eBay) rather cheap and good quality.But THE delivery time is 6 weeks.
I'm also going to do à mod because the signal is to low coming from an iPod etc
Would it be possible to use à bass treble circuit without losing audio quality ?
I've also found à shop in Belgium to deliver the p audio hp 10t( these drivers are hard to get).
In à couple of weeks i'm going to start building my qubinator .

Hey, nice to know i am not alone anymore

Sure it isn't max 6 weeks? I usually get stuff form ebay within 3 weeks, even from china. It will also take you a while to do all the woodwork, so should be good timing.

Without knowing allot about amps, i am guessing that adding bass and treble will draw more power, and may result in quality loss. Please correct me if i am wrong.

If i can give you some advice, stick to the original design with 9mm ply. Unless of course you want to spend some quality time with your router...

I just received the battery a few minutes ago, and have more or less finished the woodwork. So now i just need the amp, and i am good to go

Good luck with it.

[Kasper Jack]

Would this charger be ok for this battery?

[Saturnus]

Originally Posted by Kasper Jack

Would this charger be ok for this battery?

No. You can't use a 4 cell charger on a 3 cell battery.

[jeroendb]

[QUOTE=Kasper Jack;3158480]Madness


I have finally got round to building the Qubinator! I got a Swedish friend to import the P.audio HP-10T's, but I am still waiting for battery and amp to arrive from China, before i can glue the whole thing together.

Anyhow.. I know you guys like photos, so here's a couple of the project so far.





Why did you cut these cirkel's on the side and at the botom.
When I look at Saturnus his design in sketchup they aren't present ??

[Saturnus]

Originally Posted by jeroendb

Why did you cut these cirkel's on the side and at the botom.
When I look at Saturnus his design in sketchup they aren't present ??

It's discussed a little earlier. Kasper Jack is using 14mm plywood instead of the intended 9mm. Hence some of it has to go.

[jeroendb]

Okay thx.
Saturnus what do you think about a tone control circuit in the qubinator or is it overkill.

[Kasper Jack]

Originally Posted by Saturnus

No. You can't use a 4 cell charger on a 3 cell battery.

I know nothing about battery chargers.. How about this? If not, then which one of the chargers on the list you linked to earlier, would you recommend?

Originally Posted by jeroendb

Why did you cut these cirkel's on the side and at the botom.
When I look at Saturnus his design in sketchup they aren't present ??

^What he said

[ßart West-VL.]

Quote:
Originally Posted by jeroendb View Post
Why did you cut these cirkel's on the side and at the botom.
When I look at Saturnus his design in sketchup they aren't present ??

Originally Posted by Kasper Jack

^What he said

What Saturnus answered: The Boominator - another stab at the ultimate party machine

[Kasper Jack]

Nearly finished my Qubinator build, just missing the electronics now. First of all, will this charger work with my batteries?

I have spent all day trying to make a wiring diagram, but can't find a solution
I have bought 2x 12v batteries, a 3 way switch with 2 circuits, a fuse, a 12v AMP and a 24v AMP. I want to connect them so the 12v amp is powered by the the two batteries in parallel, and the 24v amp is powered by the batteries in serial. only one amp must be switched on at a time. I can't figure out how to connect it all together, or if it is even possible with that switch. Do i need to get a switch with more circuits, or is it somehow possible with this one?

[Kasper Jack]

Heres a diagram, i just need to draw the lines... But where???