Hallo,
I'm a new member. I'm looking for a circuit or schematic plan for the kenwood basic c2 preamp and kenwood basic m2 amp. A few weeks ago i bought a c2 and its sound is very good. Now i'm looking for a m2, but all i've found was defect amps. I suppose the powercircuits dat 1521 and/or dat 1018 have finished there life...
I've red that there is a posibility to bypass the TA2031 and than the amp maybe runs fine ... only that it runs real hot! Maybe a additional heatsink like a heatpipe for example will solve this problem??? I will try....
Can anyone explain me this bypassing? Then i can test my m2 by that. And i'm looking for a test to check the dat 1521 and dat 1018 if this piece is ok or not....
sorry for my bad english, mybe anyone can help me greenhorn ;-))
Thanks by now...
I'm a new member. I'm looking for a circuit or schematic plan for the kenwood basic c2 preamp and kenwood basic m2 amp. A few weeks ago i bought a c2 and its sound is very good. Now i'm looking for a m2, but all i've found was defect amps. I suppose the powercircuits dat 1521 and/or dat 1018 have finished there life...
I've red that there is a posibility to bypass the TA2031 and than the amp maybe runs fine ... only that it runs real hot! Maybe a additional heatsink like a heatpipe for example will solve this problem??? I will try....
Can anyone explain me this bypassing? Then i can test my m2 by that. And i'm looking for a test to check the dat 1521 and dat 1018 if this piece is ok or not....
sorry for my bad english, mybe anyone can help me greenhorn ;-))
Thanks by now...
solution from other Thread....?
Hi,
i red this bypassing-method in this forum in a thread made by the members SVI2004 and K-amps. But unfortunatly i'm a new member und so i'm under moderation. It's not allowed to me to send e-mails direct to members.... :-(.
So I've to wait.....
Maybe is my question in the wrong category placed?
Hi,
i red this bypassing-method in this forum in a thread made by the members SVI2004 and K-amps. But unfortunatly i'm a new member und so i'm under moderation. It's not allowed to me to send e-mails direct to members.... :-(.
So I've to wait.....
Maybe is my question in the wrong category placed?
You can buy the DAT1521N and DAT1521P devices, along with the Trio Kenwood TA2031 from here Buy Electronic components,Ic,Module,Transistor at UTSOURCE
$5.00AU for the DAT devices and $10.00AU for the TA2031.
As it happens I repaired an M2 recently.
$5.00AU for the DAT devices and $10.00AU for the TA2031.
As it happens I repaired an M2 recently.
Hi,
I have the M2A repair manual.
If you are interested, you can contact me by PM and I'll send you.
I just make a submition for the DAT 1018N/P, DAT 1521N/P and TA2031 for my two M2A, on the site below (Buy Electronic components,Ic,Module,Transistor at UTSOURCE).
The current price is 6$ each component ...
Thanks to Muff for this URL.
I hope this site is serious, but it seems !
I'm also interested in advices to repair a M2A, but there is a very very long time that I did not make any more electronics !
I have the M2A repair manual.
If you are interested, you can contact me by PM and I'll send you.
I just make a submition for the DAT 1018N/P, DAT 1521N/P and TA2031 for my two M2A, on the site below (Buy Electronic components,Ic,Module,Transistor at UTSOURCE).
The current price is 6$ each component ...
Thanks to Muff for this URL.
I hope this site is serious, but it seems !
I'm also interested in advices to repair a M2A, but there is a very very long time that I did not make any more electronics !
- Status
- This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button.
- Home
- Amplifiers
- Chip Amps
- kenwood basic m2 amp-circuits