http://www.partsexpress.com/webpage.cfm?&Webpage_ID=3&CAT_ID=41&ObjectGroup_ID=605&SO=2
A moderator should start a Power Supply FAQ thread and make it a sticky...
A moderator should start a Power Supply FAQ thread and make it a sticky...
ok, i may be an idiot
ok, i apologize for my ignorance. i do believe i have been misinterpreting just exactly what 18v+18V, 24v+24v, et cetera mean.
so correct me if i am wrong (still), but actually this (for instance) transformer:
http://www.partsexpress.com/pe/showdetl.cfm?&Partnumber=122-650
is exactly what i need for a power supply along the lines of carlos machado's snubberized psu?
ok, i apologize for my ignorance. i do believe i have been misinterpreting just exactly what 18v+18V, 24v+24v, et cetera mean.
so correct me if i am wrong (still), but actually this (for instance) transformer:
http://www.partsexpress.com/pe/showdetl.cfm?&Partnumber=122-650
is exactly what i need for a power supply along the lines of carlos machado's snubberized psu?
35+35 is the "dual secondary" part of the product description.
This is too high for a LM3886.
35*1.414=49 volts while max supply voltage is 84 volts (+/- 42 VDC). It would most likely work and only let out the magic smoke very occasionally... it's just too high.
The next question is the impedance of the speakers you MIGHT be using.
You should start reading the data sheet.
http://www.national.com/pf/LM/LM3886.html
This is too high for a LM3886.
35*1.414=49 volts while max supply voltage is 84 volts (+/- 42 VDC). It would most likely work and only let out the magic smoke very occasionally... it's just too high.
The next question is the impedance of the speakers you MIGHT be using.
You should start reading the data sheet.
http://www.national.com/pf/LM/LM3886.html
BWRX said:A moderator should start a Power Supply FAQ thread and make it a sticky...
Or a member with enough time and experience on the subject... we'll gladly make it sticky.
/Hugo
dual secondary trans, snubbers
Burnded fingers,
In a normal center tap 4 doides are used in the bridge +/-,-/+ and center "full wave".
In a dual secondary 2 bridges are used and the centertap is taken by connecting the + from the top bridge to the - of the bottom" full wave*2" the result is less ripple, I guess you could call it artificial dual phase
Snubbers have been around from the dawn of electronics, they help "snub out" unwanted frequency,s on the DC line, some frequency variations from the outputs collectors or emitters will make it onto the DC supply lines, snubbers RC networks help elliminate these. There primary use was in RF circuits to elliminate RF hash on the supply.
Burnded fingers,
In a normal center tap 4 doides are used in the bridge +/-,-/+ and center "full wave".
In a dual secondary 2 bridges are used and the centertap is taken by connecting the + from the top bridge to the - of the bottom" full wave*2" the result is less ripple, I guess you could call it artificial dual phase
Snubbers have been around from the dawn of electronics, they help "snub out" unwanted frequency,s on the DC line, some frequency variations from the outputs collectors or emitters will make it onto the DC supply lines, snubbers RC networks help elliminate these. There primary use was in RF circuits to elliminate RF hash on the supply.
dual secondary trans
Here is a schematic that I use for the PS of one of my small BPA amps that used 2* dual complimentary rectifiers (DRC)
Here is a schematic that I use for the PS of one of my small BPA amps that used 2* dual complimentary rectifiers (DRC)
An externally hosted image should be here but it was not working when we last tested it.
Re: dual secondary trans, snubbers
Some say the 0volt ground connection is quieter in the dual sec+DUAL rect version But I have not been able to measure any difference.
The main difference is the extra voltage lost through the extra rectifier and the extra cost.
And how did THAT WORD miss the dictionary? It always excludes my completely innocent use if it.
absolutely wrong. The smoothing of both the centre tapped into single rectifier into series caps and dual secondary into dual rectifiers into dual single caps is exactly the same.halo0925 said:.......In a dual secondary 2 bridges are used and the centertap is taken by connecting the + from the top bridge to the - of the bottom" full wave*2" the result is less ripple.........
hash
Some say the 0volt ground connection is quieter in the dual sec+DUAL rect version But I have not been able to measure any difference.
The main difference is the extra voltage lost through the extra rectifier and the extra cost.
And how did THAT WORD miss the dictionary? It always excludes my completely innocent use if it.
- Status
- This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button.
- Home
- Amplifiers
- Chip Amps
- dual secondary transformers