Copy of Kore-Eda pre ?

sinski · 29th April 2006, 02:31 PM

They are two new products from Sakura.

http://www.sakurasystems.com/products/koreeda.html

Maybe it will be easy to make a copy of the preamp ?

Can anybody identify the components in the preamp ?

As far as i can see they use:

1. Small transformer from Talema/India with 2x115V input and two 2.5VA 15V AC outputs

2. Two rectifiers composed from four normal diodes

3. Two bigger caps, probably 3300/25V Panasonic TS-HA?

4. 78xx and 79xx regs with two small electrolyt caps - decoupling caps ?

5. Preamp section with adXXX opamps ?

6. Small red tantalum caps close to opamps ?

7. Around opamps they are four resistors

8. One polystyren/aluminium input? output ? cap from BC ?

Can anybody identify more details and maybe create the schematic of this small pre ?

Who knows, maybe it sounds very good.

Cheers, sinski

sinski · 3rd May 2006, 03:04 PM

This is the link for preamp picture :

http://s7.photobucket.com/albums/y25...&current=2.jpg

I am completely electronic newbie and have no to much knowledge about electronics. In the last days i was just reading about opamp based pres and looked carefully on Kore Eda pre.

I found the SWCAD software from LT and i created a circuit, which could be the pre, but i am not sure about it.

http://s7.photobucket.com/albums/y25...oreedapre1.jpg

Can anybody help and say if it is OK ?

What about

R1=2K
R2=100K
R3=1K
R4=2K

C1=10uF
C2,C3 4.7uF

Any ideas ?

sinski

jaudio · 4th May 2006, 12:03 PM

You need to add a .1uf caps to the supply rails. I would also go over the datasheet,there are suggests for the resistors values. It may have a min. gain requirement also.

29th April 2006, 02:31 PM	#1
sinski diyAudio Member Join Date: Sep 2004 Location: Audio Shambala	Copy of Kore-Eda pre ? They are two new products from Sakura. http://www.sakurasystems.com/products/koreeda.html Maybe it will be easy to make a copy of the preamp ? Can anybody identify the components in the preamp ? As far as i can see they use: 1. Small transformer from Talema/India with 2x115V input and two 2.5VA 15V AC outputs 2. Two rectifiers composed from four normal diodes 3. Two bigger caps, probably 3300/25V Panasonic TS-HA? 4. 78xx and 79xx regs with two small electrolyt caps - decoupling caps ? 5. Preamp section with adXXX opamps ? 6. Small red tantalum caps close to opamps ? 7. Around opamps they are four resistors 8. One polystyren/aluminium input? output ? cap from BC ? Can anybody identify more details and maybe create the schematic of this small pre ? Who knows, maybe it sounds very good. Cheers, sinski

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Quad 606 copy	proba55555	Analogue Source	4	24th September 2007 11:58 PM
Cyrus PSX-R copy	dubh	Solid State	3	7th February 2007 04:59 PM
DAT Copy protection	richardsymes	Digital Source	16	30th July 2006 05:53 PM
Sure, copy an amp. . . It'd work but I'm looking for something different.	PhoenixFL	Tubes / Valves	6	13th May 2004 03:12 AM
Does anyone have a copy of WinAIRR 4?	M_Anker	Multi-Way	2	25th December 2001 05:57 PM

New To Site?	Need Help?
Register to Participate Search Privacy Statement Contact Us	Frequently Asked Questions Did you forget your password? Mark Forums Read


	Please consider donating to help us continue to serve you. Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving

3rd May 2006, 03:04 PM	#2
sinski diyAudio Member Join Date: Sep 2004 Location: Audio Shambala	This is the link for preamp picture : http://s7.photobucket.com/albums/y25...&current=2.jpg I am completely electronic newbie and have no to much knowledge about electronics. In the last days i was just reading about opamp based pres and looked carefully on Kore Eda pre. I found the SWCAD software from LT and i created a circuit, which could be the pre, but i am not sure about it. http://s7.photobucket.com/albums/y25...oreedapre1.jpg Can anybody help and say if it is OK ? What about R1=2K R2=100K R3=1K R4=2K C1=10uF C2,C3 4.7uF Any ideas ? sinski

4th May 2006, 12:03 PM	#3
jaudio diyAudio Member Join Date: Oct 2004	You need to add a .1uf caps to the supply rails. I would also go over the datasheet,there are suggests for the resistors values. It may have a min. gain requirement also.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)