Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Chip Amps Amplifiers based on integrated circuits

Clipping Indicator
Clipping Indicator
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Thread Tools Search this Thread
Old 5th April 2005, 08:08 AM   #1
scott_jcp is offline scott_jcp  United States
diyAudio Member
Join Date: Feb 2005
Location: Richardson, TX
Default Clipping Indicator

I want to add a clipping indicator to my Gainclone.

I found a schematic at http://www.sound.westhost.com/project23.htm, but I have a few questions.

1) The text seems to indicate I can input another amp at A to monitor multiple amps at once. I would like to do this, seeing as my amp is stereo, but how do I connect the + and - outputs of the second amp at A?

2) What are the 3 resistors, cap, and diode connected to at the bottom right?

3) When he says the opamp +Ve pins are connected to the 12V Zener, what exactly does that mean with respect to the wiring?
  Reply With Quote
Old 5th April 2005, 01:25 PM   #2
macboy is offline macboy  Canada
diyAudio Member
Join Date: Oct 2003
Location: Ottawa, Canada
First off, I would strongly recommend project 57 instead. It works by actually detecting the distortion created by clipping. But I'll also answer your questions:

1. You see that lonely diode at the bottom, connected on only one side with the other side labelled "A"? Well, that's for (one of) the other amps that you connect. You can see the corresponding diode for the first channel directly above it. You need to build the first half of the circuit (everything up to and including U1A) once for each amp that you want to connect, but each of those connects to this same point, each through it's own diode.

2. U1B and all that stuff hanging off of it creates a peak hold detector. Basically it makes sure that a very brief pulse at the input (indicating the amp clipping very briefly) is stretched out in time long enough for you to see the LED clipping indicator. If the LED was to only light exactly when the amp was clipping, you wouldn't even notice it until you were clipping really badly.

3. The opamp(s) postive supply pin (+Ve) will connect to the cathode end of the zener. The zener (with resistor labelled "see table 1") is acting as a shunt regulator to create a 12 V power supply for the opamps.
  Reply With Quote
Old 5th April 2005, 01:27 PM   #3
Giaime is offline Giaime  Italy
diyAudio Member
Giaime's Avatar
Join Date: Oct 2004
Send a message via MSN to Giaime
1) I think that you must duplicate the whole circuit before of the A point to connect something to that point. I mean the two trannies, the first opamp section... The text is just saying that the only thing you couldn't do is to use the same circuit for different power supplies...

2) Do you mean the 1uF cap and 100k resistor? I think that they are used to "stretch" the clip pulse to light the led for a longer interval, just because it would be too short to see.

3) The writer is not clear about that; refer to the schematic on top of the page for wiring.

Hope this helps...

Edit: oh, I just saw another one who explained better...
  Reply With Quote


Clipping IndicatorHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Power Amplifier Clipping Indicator widi Solid State 2 1st March 2007 02:50 AM
DC Protection and Clipping Indicator BobEllis Everything Else 15 5th February 2007 06:34 AM
Rod Elliot's Clipping Indicator Devil_H@ck Parts 6 31st May 2006 08:16 AM
Zen clipping indicator Vix Pass Labs 11 18th November 2004 08:08 AM
Good clipping indicator? hugobross Solid State 7 19th January 2002 06:59 PM

New To Site? Need Help?

All times are GMT. The time now is 03:58 AM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 16.67%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Copyright ©1999-2018 diyAudio