
Home  Forums  Rules  Articles  diyAudio Store  Blogs  Gallery  Wiki  Register  Donations  FAQ  Calendar  Search  Today's Posts  Mark Forums Read  Search 
Chip Amps Amplifiers based on integrated circuits 

Please consider donating to help us continue to serve you.
Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving 

Thread Tools  Search this Thread 
12th February 2005, 02:47 PM  #1 
diyAudio Member
Join Date: Jan 2004
Location: KC Metro

First Wattish Chip Amp, Variable Impedance
Nelson Pass's F1 amplifier got me to begin exploring current amps which lead me to variable impedance which lead me to realize I obviously don't get some basics.
I was looking at http://sound.westhost.com/project56.htm Figure one is intuitive for both voltage and current amps. Figure two and the voltages into 8 and 4 ohm loads has me stumped. The 18.8 with no load is straight forward enough, but I can't get to the 12.8 and 9.7 volt calculations. My guess was that for quick and dirty calculations gain is going to be set by r1 and (r2+r3) in both open and under load calculations. If so (and it appears not to be), I would have expected Load and r3 to give me the reported voltages under load as a simple voltage divider with 18.8 as the Vin. I suspect that I am grossly over simplifying. Can anyone point me in the right direction? 
12th February 2005, 03:36 PM  #2 
diyAudio Member
Join Date: Dec 2003
Location: Near Seattle

One thing to keep in mind is that he measured those values and didn't calculate them because he doesn't know the output impedance. You're doing those calculations assuming negligible output impedance compared to the load. That's a usual "rule of thumb" for voltage sources (most opamps). But in this case you have 3.75 ohms output impedance. So you can't ignore it because, it's basically like having 3.75 ohms in series with the output and before R1,R2,R3,Rl. Try adding a 3.75 ohm resistor between the output and R1 and then recalculating and see what you come up with.
 Danny 
12th February 2005, 07:10 PM  #3  
diyAudio Member
Join Date: Jan 2004
Location: KC Metro

Quote:
My goal is to sketch out a current amplifier with an 80ohm output impedence (following the F1's lead here if not all the way to class a and zero feedback). To do that I need to know how to calculate 1) The no load voltage (no problem) 2) Vout under load (don't understand... ) 3) Output impedence (well document in Project 56 based upon the availability of 1 and 2) Being able to calculate Vout under load where output impedence is *not* known, is the missing link. 

13th February 2005, 05:27 PM  #4  
diyAudio Member

Quote:
__________________
There are still unbridgeable divisions between cultures. How can two peoples ever come to understand each other when one of them is ignorant of Totò? Umberto Eco 

Thread Tools  Search this Thread 


Similar Threads  
Thread  Thread Starter  Forum  Replies  Last Post 
Impedance analyzer on a chip  jackinnj  Solid State  0  17th May 2008 01:27 PM 
Simulating variable output impedance  abzug  Solid State  3  30th December 2007 06:47 AM 
BOSOZvariable impedance volume attenuator  jh6you  Pass Labs  22  15th March 2005 08:34 AM 
How to measure the output impedance of the DAC chip  ergo  Solid State  2  9th June 2004 07:07 AM 
TI Introduces Industry's First Fully Integrated, SingleChip 100Watt Digital Audio A  mikejz84  Chip Amps  14  9th December 2003 07:37 AM 
New To Site?  Need Help? 