LM3886 gain clone vs STK4048XI for 4 ohm load - diyAudio
Go Back   Home > Forums > Amplifiers > Chip Amps

Chip Amps Amplifiers based on integrated circuits

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 25th September 2004, 12:05 PM   #1
filgor is offline filgor  Australia
diyAudio Member
 
Join Date: Sep 2004
Location: Sydney
Question LM3886 gain clone vs STK4048XI for 4 ohm load

I am questioning wheather I should use a single STK4048 or three LM3886's in gain clone parallel (each seeing 12ohms) to drive a 4 ohm (2.83+2.83j semi-reactive) load.
I will be Using a heatsink rated at 0.74degC/W

Has any one done a real analysis on the STK4048XI using regulated power supplies and or 4ohm loads?

The datasheets available from Sanyo for the STK range are somewhat opaque compared to the National semiconductor datasheets for the LM3886.

What I am resonably sure of from the available data is that the three LM3886's in parallel would provide lower distortion but would have a higher thermal resistance as follows.

Distortion:
0.03% at 0.1 watt at 20KHz 8ohm for STK4048XI from data sheet'
0.02% at 0.1 watt at 20KHz 4ohm for 2 x LM3886 in parallel (each seeing 8ohm).
one could only assume the STK4048 is worse at 4 ohm and that 3 LM 3886's in parallel provides lower distortion than 2.

Thermal resistance:
1.4/3=0.47deg.c/W for 3 x LM3886 as apposed to 1.2/4=0.3deg.c/W degrees c/W for the STK4048... MUCH better!

The other factors I am aware of are as follows:

1. The LM3886 has built in thermal shutdown

2. Maximum supply voltage. The LM 3886's will only tolerate +/- 42 volts while the STK will take a whopping +/-87 volts... BIG difference!

3. The convinience of one STK4048 IC as appossed to three LM3886's with 3 sets of matched feedback networks and output resistors!

4. In Australia one STK4048XI is much cheaper than 3 LM3886's

Has any one got any information that is contrary to any of the above or that would be useful in my decision?
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
FS: LM3886 Gain Clone Chips (19) bolserst Swap Meet 5 26th October 2008 06:35 PM
How to figure gain on split-load with positive feedback? GordonW Tubes / Valves 4 21st May 2008 05:24 PM
Best MC Load Resistor Type, current gain stage... tubenut Analogue Source 29 4th September 2006 10:43 AM
Plate load for 6SN7 gain stage? G Tubes / Valves 53 16th July 2003 10:07 AM


New To Site? Need Help?

All times are GMT. The time now is 04:09 PM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2