|Chip Amps Amplifiers based on integrated circuits|
Please consider donating to help us continue to serve you.
Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
||Thread Tools||Search this Thread|
|25th May 2004, 10:18 AM||#1|
Join Date: Dec 2001
Location: SIUE, Illinois, USA
lm4780 omniPCBs soon to be for sale
this is likely a limited run thing, very limited run probably.
in anycase i've been working on an easy to use, extremely versitile lm4780 board.
if you've emailed me before about these, i will email you back tomorrow with the results of the prototypes.
the board is larger though, 2.5"x2.8" (6.35 x 7.112).
the good is that the board supports many different topologies:
noninverting (AC-coupled, RF filter, and fixed volume offset options)
inverting (AC coupled option)
unbalenced differential - aka difference amplifer, often listed as a balenced to unbalenced converter, it will do this, but it doesn't have the same performance of a real balenced amplifier.
there is room for a zobel.
bridged mode is possible.
parallel mode is hopeful -- no room has been alloted on board for 0.1 ohm resistors. i have a hunch they aren't needed if you make the hookup wire long/thin enough...
stereo mode is possible.
each signal ground is seperate from powerground.
the current loop should be pretty well minimized.
there are 2 screw holes and room for connectors, thus making setup and mounting easier.
chip is mounted 1/2 inch (1.25cm) away from the PSU caps, allowing for a clamp-mounting bracket to be used.
any questions, i will try to answer.
as i said, this isn't really a group order, it's just a limited run. i tried to optimize the board for low noise and for fairly easy use. that being said, you must still be able to solder.
as i have seen, there are currently two other 4780 board out, one by brianGT and one by OddOne. if you are looking for a parallel amp with the 4780, i'd probably go with one of those, they seem to garuentee it, and mine is just "it should work".
i should be making pcbs today at 8pm. if all goes well, i will have a finished product on a scope by midnight and a review tomorrow.
if only it could be used for good, not evil...
|6th July 2004, 09:31 AM||#2|
Join Date: May 2004
Here I found and bought 4 boards for the LM4780 chips, double sided as per national board, gold plated, etc excellent quality !!
Here is the page in Korea.http://www.speaker.ne.kr/home/index.php?cmn=1&cma=
The boards can be purchased with parts as req.
My boards were $10 Aust each, plus postage. ordered Thursday, and received the next Tuesday in Perth !!!!
|Thread Tools||Search this Thread|
|Thread||Thread Starter||Forum||Replies||Last Post|
|For sale Upupa Epops' Stereo Chip Amplifiers PA-03 Gainclone LM4780 - assembled PCBs||cough||Swap Meet||0||27th January 2009 03:37 PM|
|sonic differences between inverting/non-inverting LM4780 VS both non-inverting LM4780||jarthel||Chip Amps||5||19th July 2007 12:37 PM|
|LM4780 & LM3886 PCBS in India for sale.||kuldeepsingh||Swap Meet||0||31st March 2007 02:29 AM|
|for sale: lm3886 and lm4780||elementx||Swap Meet||2||21st July 2006 03:14 PM|
|LM3886, LM3875, LM4780 for sale/trade||elementx||Swap Meet||0||6th December 2005 04:15 PM|
|New To Site?||Need Help?|