
Home  Forums  Rules  Articles  diyAudio Store  Blogs  Gallery  Wiki  Register  Donations  FAQ  Calendar  Search  Today's Posts  Mark Forums Read  Search 
Chip Amps Amplifiers based on integrated circuits 

Please consider donating to help us continue to serve you.
Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving 

Thread Tools  Search this Thread 
15th February 2013, 10:42 PM  #1 
diyAudio Member
Join Date: Aug 2004
Location: Argentina

Is this the right way to Calculate an Transfomer?
Example 1.
Chipamp 70W por channel, if i build an stereo Amp, i need to use something like... Voltage 24024 = 48V AC => 68 VDC  2 Volt from diodes = 66VDC 140W Power To be safe i need to use 140W x 1.4 = 200VA Amperage = 4.15A So for an 2 channels amp with 200VA will be OK, right? If use one channel instead two (to run mono) can use the half of that values Voltage 24024 = 48V AC => 68 VDC  2 Volt from diodes = 66VDC 70W Power To be safe i need to use 70W x 1.4 = 100VA Amperage = 2.1A Right? What is the diference in the maths if i use 8ohms, 6ohms, 4 ohms or 2 ohms load? 
16th February 2013, 12:29 AM  #2 
diyAudio Member
Join Date: Apr 2008
Location: Carlisle, England

If the amplifier is 100 watts then you need 140VA as 40% of power is lost in the heatsink and 60% goes to the speaker.
__________________
PCBCAD51 pcb design software. http://www.murtonpikesystems.co.uk 
16th February 2013, 01:44 AM  #3 
diyAudio Member

I created an Excel spreadsheet to do these kind of calculations. It is useful for designing a power supply, checking out how a given transformer will perform, and to estimate the maximum power that a class AB amplifier (e.g. a chip amp) will put out for a given power supply.
Get it at this link: Free Audio Software! It's called "Power Supply Capability and Design". If you have questions about it, send me a PM or (better) use my web site to contact me. Charlie 
18th February 2013, 10:41 PM  #4  
diyAudio Member
Join Date: Nov 2006
Location: Indiana

Quote:
peak signal voltage = peak rail voltage  pp ripple voltage  about 4 volts The "about 4 volts" is for the amplifier itself, usually a Vce voltage plus the voltage across a lowvalue resistor. Usually 3 to 4 Volts at max power. It might be more than 4 V, depending on amplifier topology. But it probably won't be much less than 3 V. So assuming 1V pp ripple, that leaves about 27 V for the output signal peak. The RMS voltage of a maximumamplitude sine would then be 19 V. RMS output power would be V²/Rload, or i²·Rload. Max RMS Output Power would be 19²/8 = 45 W into 8 Ohms, or 60 W into 6 Ohms, or 90 W into 4 Ohms, or 180 W into 2 Ohms. To get 70 W into 8 Ohms, V²/8 = 70 W Vrms = 23.7 V Vpeak = 33.5 V Vrail_pk = 33.5 + 4 + Vripple_pp = 38.5 V (if Vripple = 1 V pp) Vrms _xfrmr = (38.5 + 2) / √2 = 28.6 VMRS Rather than taking 1.4 times the needed VA, it would be better to use a factor of at least 3 or more. 

19th February 2013, 01:09 AM  #5  
diyAudio Member

Quote:
For instance, you can choose a higher rail voltage and allow more sag under load, or you can choose to use a lower rail voltage and demand a stiffer supply. The choice might depend on the max rail voltage that your amp can survive, or thermal dissipation concerns, cost of PS, etc. There can be lots of tradeoffs, so I don't think that there is a good ROT for this, except to model the transformer and PS performance under load. I know you (Bob) put together some spreadsheets for calculating this kind of thing, and my spreadsheet (linked in my post above) also does this kind of calculation. I have found that in most cases, with a typical "music" signal the transformer can be as low as 1.5 times the maximum power output capability of the amp, given that with music signals the amplifier will mostly be operating at a much lower average power level and demand for high power levels is very short in duration and can be (mostly) supplied by the bank of caps in the PS. Do you find something else with your work? Charlie Last edited by CharlieLaub; 19th February 2013 at 01:15 AM. 

19th February 2013, 01:16 AM  #6 
diyAudio Member
Join Date: Apr 2008
Location: Carlisle, England

Its quite difficult to rate a transformer for an amplifier because the current draw isn't constant.
The smoothing capacitors take in surges of current at the peak of the sine output from the transformer. This means you can easily take full current from the transformer for short periods. So its not as simple as an amp requiring 2amps taking two amps constantly. Its more likely to take 6+ amps in a surge.
__________________
PCBCAD51 pcb design software. http://www.murtonpikesystems.co.uk 
19th February 2013, 01:57 AM  #7 
diyAudio Member
Join Date: Aug 2004
Location: Argentina

wow, thanks too much!
I have an PCB from an rectifier that used with an CT transformer. I have another proyect in mind that dont need + i just need 060V, want to know if is possible to convert or need to use a new PCB, i think that the schematic is similar to this 6*10000uF¸ßµµ¹¦·ÅµçÔ´°å  ¹¦·Å°å  ¹¦·ÅµçÔ´  öÎ¶¼µç×ÓÍø sorry for the offtopic question, but think that the answer will be not enough hard to create a new post 
19th February 2013, 02:00 AM  #8 
diyAudio Member
Join Date: Nov 2006
Location: Indiana

Charlie and Nigel,
Well, "better" means better. I agree that there isn't a very good rule of thumb for this. I wanted to try to have the OP make sure that he left a generous margin, something about double the 1.4X he was going to use, since that leaves no margin at all. (And I really like the idea of having railvoltage margin, mainly for headroom for transients, but didn't want to complicate it too much.) Probably the only way to really do it right is to account for the effects of transformer windings' leakage inductances, and their resistances, and the diodes' ontoofftime ratio, etc etc. My spreadsheet does solve and simulate the circuit's differential equations (2nd order when diodes are on and 1st order when diodes are off) and also figures out exactly when the diodes turn on and off, and takes into account the capacitor ESR (but not ESL) and plots everything as functions of time. But I guess it does not take into account the heatsink losses. Also, possibly the actual transformer being used would need to be modeled. The one in my spreadsheet is modeled from a real transformer, and is scalable in terms of VA rating, Vrms output voltage, input frequency, and input voltage. But transformers vary and may need their own model, for accurate results. The spreadsheet does include the instructions for measuring a new transformer, and will automatically create a new model from the measurements. And, I used a particular Schottky diode, for the rectifier diodes. That could be easily changed, too, by changing the diode's equation in the VBA code. The model and the procedure I used to obtain the model are in the PDF file describing the spreadsheet, in the post at Power Supply Resevoir Size . Also note that my spreadsheet performs a worstcase analysis, in terms of the output signal. It assumes a constant DC output current that is at the level that the PEAK current would be at, for a sine output at the max rated power. The spreadsheet's latest version, for Excel 2007 and later, is downloadable from the post at: Power Supply Resevoir Size If someone needs the Excel 952003 version, it is downloadable from the post at: Power Supply Resevoir Size Cheers, Tom Last edited by gootee; 19th February 2013 at 02:17 AM. 
19th February 2013, 02:46 AM  #9 
diyAudio Member
Join Date: Nov 2006
Location: Indiana

In post # 4, the Vrms transformer voltage that I calculated, to be able to get 70 W RMS max output power, is not high enough. It only enables about 60 W RMS max, into 8 Ohms. I forgot to account for transformer losses, I think.
It's best to use the spreadsheet. 
Thread Tools  Search this Thread 


Similar Threads  
Thread  Thread Starter  Forum  Replies  Last Post 
Multitap Transfomer  lithoc  Power Supplies  3  10th March 2011 10:13 AM 
another transfomer question  AltecDarpa  Power Supplies  1  2nd April 2010 07:10 PM 
peerless transfomer information  nhuwar  Tubes / Valves  17  18th January 2007 01:07 PM 
Input transfomer on P3A  jesper  Solid State  9  30th October 2004 07:39 PM 
Think this is worth $60? (transfomer)  Hybrid fourdoor  Swap Meet  5  22nd June 2004 10:56 AM 
New To Site?  Need Help? 