16 Ohm Speakers - Page 3 - diyAudio
Go Back   Home > Forums > Amplifiers > Chip Amps

Chip Amps Amplifiers based on integrated circuits

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 21st November 2012, 09:38 PM   #21
diyAudio Member
 
danielwritesbac's Avatar
 
Join Date: Nov 2007
Quote:
Originally Posted by tinitus View Post
or in series
VA(watt) rating comes out the same anyway
its always the total of the whole trafo
Ampere rating is each secondary
Thank you for the unconfuse!
I was accustomed to buying EI-core center tap (always secondaries series), but the Antek toroid dual secondaries datasheets (always secondaries paralleled) baffled me since their test conditions never match my application.

P.S.
A possible chip amp for 16 ohm speakers is bridged TDA7265 monoblocs, and these can run from $9 19vdc laptop power pack. However, the datasheet bridge application's gain setting looks like a misprint. I think I'd use the non-bridge schematic, change the feedback resistors to 27k and then apply simple one resistor bridge. That plan makes only about 11 watts to 16 ohms though. That is a very effective 11 watts if one adds about 1000u series to the + amplifiers output (DC block, speaker protect, current drive) and adds resistors to the - amplifiers output with the value matching or greater than the ESR of the + amps output caps. Sort of an inexpensive current drive setup that way, and minimal loss too. Would be a non-shouty chip amp. Some people enjoy that chip for mids-n-treble amp in bi-amp systems.
__________________
Tools, Models & Software for DIYClipNipper boostLM1875 TurboPowerful TDA7293 kitTDA7294 pt2pt ♦ My post has opinion.

Last edited by danielwritesbac; 21st November 2012 at 10:02 PM.
  Reply With Quote
Old 22nd November 2012, 04:33 PM   #22
sreten is offline sreten  United Kingdom
diyAudio Member
 
Join Date: Nov 2003
Location: Brighton UK
Quote:
Originally Posted by tinitus View Post
based on more ampere for low imp speaker load,
I would say reality is mostly the opposite in general
you will have to lower VA rating to achieve this
Hi, the reality is you are mostly wrong, rgds, sreten.

Work out the VA ratings for an amplifier
that does 50W/8ohm and 80W/40hm.
__________________
There is nothing so practical as a really good theory - Ludwig Boltzmann
When your only tool is a hammer, every problem looks like a nail - Abraham Maslow
  Reply With Quote
Old 22nd November 2012, 04:44 PM   #23
sreten is offline sreten  United Kingdom
diyAudio Member
 
Join Date: Nov 2003
Location: Brighton UK
Quote:
Originally Posted by danielwritesbac View Post

... here is a different option for current drive at only the bass ...
... Carefully chosen roll-off has a current drive effect potentially useful for bass extension ...
Hi,

No it doesn't. Simple capacitor coupling outside the feedback loop is the
same as capacitor coupled speakers* (so called third order speakers),
and the effect is very speaker dependent but can work well.

rgds, sreten.

* Numerous models from Kef, Goodmans, Wharfedale etc.
The capacitor needs to match the speaker properly.
__________________
There is nothing so practical as a really good theory - Ludwig Boltzmann
When your only tool is a hammer, every problem looks like a nail - Abraham Maslow
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Matching my 8 ohm amp to 16 ohm speakers. DocJDG Solid State 9 21st April 2013 12:57 PM
Which amp should I built for my 16 ohm speakers? ajohn Pass Labs 7 15th March 2010 12:38 AM
F3 With 16 ohm Speakers? TV Man Pass Labs 3 17th March 2009 03:08 PM
16 ohm speakers moreismore Chip Amps 2 1st January 2005 12:53 PM
Zen V4 and 16 ohm speakers selder Pass Labs 11 21st December 2002 03:13 PM


New To Site? Need Help?

All times are GMT. The time now is 02:51 PM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2