My_Ref Fremen Edition RC - Build thread

Status
This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button.
Member
Joined 2005
Paid Member
Hi all,

in this thread we will discuss about building the My_Ref Fremen Edition using the Release Candidate boards.

We also discuss listening evaluations and, eventually, further improvements.

I've attached schematic, silkscreen and BOMs

To build it you will need:

  • soldering iron
  • thin solder
  • tacky flux
  • tweezers
  • a good sight or a magnifier ;)
In the next posts I'll illustrate my build as a tutorial.
 

Attachments

  • My_Ref_FE RC - Schematic.pdf
    44.9 KB · Views: 2,370
  • My_Ref_FE RC - Silkscreen.pdf
    53.9 KB · Views: 896
  • My_Ref_FE RC - BOM.pdf
    11.2 KB · Views: 994
  • My_Ref_FE RC - BOM (On a budget).pdf
    8.7 KB · Views: 724
Last edited:
Member
Joined 2005
Paid Member
1 - SMD parts

Clean boards with alcohol.

The first component we put in place is the LM318.

Apply flux to pads:

attachment.php


Then position the LM318 (take care to pins to pad alignment) and keep it in place with tweezers:

attachment.php


Apply the wet solder tip to one of the pins (the bottom one on the right is NC so it's a good one to use)

attachment.php


Now that the LM318 is kept in place by the soldered pin we solder all the others.

Just apply the solder and solder tip for 1-2 seconds

attachment.php


This should be the result:

attachment.php
 

Attachments

  • 1 flux on lm318 pads.jpg
    1 flux on lm318 pads.jpg
    185.2 KB · Views: 5,189
  • 2 lm318 in place.jpg
    2 lm318 in place.jpg
    149.6 KB · Views: 5,172
  • 3 solder one pin of lm318.jpg
    3 solder one pin of lm318.jpg
    192.4 KB · Views: 5,156
  • 4 solder LM318.jpg
    4 solder LM318.jpg
    156.5 KB · Views: 5,216
  • 5 lm318 soldered.jpg
    5 lm318 soldered.jpg
    142.3 KB · Views: 5,157
Member
Joined 2005
Paid Member
We then proceed with 0805 compensation resistors and cap, starting from C34.

Apply flux:

attachment.php


position the component and while keeping it in place with tweezers apply the wet tip to one side.

attachment.php


then apply solder and tip to the other end

attachment.php


Result

attachment.php
 

Attachments

  • 6 flux on c34.jpg
    6 flux on c34.jpg
    139.8 KB · Views: 5,013
  • 7 c34 one end.jpg
    7 c34 one end.jpg
    167.6 KB · Views: 4,949
  • 8 c34 other side.jpg
    8 c34 other side.jpg
    135.1 KB · Views: 4,929
  • 9 c34 soldered.jpg
    9 c34 soldered.jpg
    146.1 KB · Views: 4,932
Member
Joined 2005
Paid Member
The next component will be the MELF diode D3.

As usual apply flux, keep it in place using tweezers

attachment.php


and apply the wet tip to one end (for melf you'll need a well wet tip).

Apply solder and tip to the other end.

This should be the result

attachment.php


Now, like we did for LM318 we proceed with D1 and D2 (flux, solder one pin while keeping the part in place with tweezers, solder the other pins)

attachment.php
 

Attachments

  • 12 keep d3 in place.jpg
    12 keep d3 in place.jpg
    156.4 KB · Views: 4,808
  • d3 soldered.jpg
    d3 soldered.jpg
    39.2 KB · Views: 4,710
  • 14 d1 d2 soldered.jpg
    14 d1 d2 soldered.jpg
    199.4 KB · Views: 4,746
Member
Joined 2005
Paid Member
Now the we know how to solder SMD parts and made some experience, we proceed with all other resistors (pay attention to orientation)

attachment.php


Note that 3K3 resistors are 0805 ones soldered on 1206 pads.

Mouser don't stock in this moment 1206 3K3 Susumus so in BOM 0805 ones are indicated.
 

Attachments

  • 15 all smds soldered.jpg
    15 all smds soldered.jpg
    256.7 KB · Views: 4,691
Member
Joined 2005
Paid Member
2 - Trough hole parts

I suggest to mount standoffs before starting this phase.

Screws will stabilize board when it's reversed for soldering

attachment.php


The golder rule is starting from lower profile parts so we'll start from DC protection resistors.

Using pliers to bend leads helps to obtain a nice looking build.

Solder parts on both boards, alternating them, it would be easier and let parts cool.

attachment.php


After bending leads mount the resistors in posistion and turn the board

attachment.php


Then solder first one side of both resitors

attachment.php


Then proceed with other side after the second board is done.

Proceed with other 1/4W resistors

attachment.php


Note that I've left unsoldered thermals pads, we'll do the same for all thermals so we can solder them later with a higher soldering temperature.

If possible keep same orientation, it will look better

attachment.php
 

Attachments

  • 16 standoffs.jpg
    16 standoffs.jpg
    163.6 KB · Views: 4,607
  • 17 pliers.jpg
    17 pliers.jpg
    157.3 KB · Views: 4,597
  • 18 turned board.jpg
    18 turned board.jpg
    139.9 KB · Views: 4,553
  • 19 solder one side.jpg
    19 solder one side.jpg
    475.4 KB · Views: 4,571
  • 20 leave thermals unsoldered.jpg
    20 leave thermals unsoldered.jpg
    148.3 KB · Views: 4,499
  • 21 keep same orientation.jpg
    21 keep same orientation.jpg
    190.1 KB · Views: 4,479
Member
Joined 2005
Paid Member
Next lower profile components are the 14V zeners, bend leads first

attachment.php


Use same tecnique used for resitors (mount parts, turn the board, solder one lead for each part, do the same on the other board, solder the remaining lead)

attachment.php


Then solder the 1N4001

attachment.php


We can start with 1/2W resistors, from R10

Note in the next picture the correct orientation the gold (tolerance) band represent the point of the arrow.

attachment.php


In this phase you should choose which C9/R10 arrangement to use.

I suggest the new one

attachment.php


Note that Rikens have opposite orientation (tolerance red band goes opposite to the arrow)

attachment.php


KOA SPR orientation, note that the marking on board have same orientation of the one on resistor.

attachment.php


Note the thermal pad left unsolderd also for the KOA...

This is the lower profile parts soldering result

attachment.php
 

Attachments

  • 22 bend zener leads.jpg
    22 bend zener leads.jpg
    136.8 KB · Views: 4,402
  • 23 14V zeners.jpg
    23 14V zeners.jpg
    218.1 KB · Views: 4,416
  • 24 1n4001.jpg
    24 1n4001.jpg
    178.9 KB · Views: 4,403
  • 25 half watt orientation.jpg
    25 half watt orientation.jpg
    199 KB · Views: 4,358
  • 26 C9R10 arrangement.jpg
    26 C9R10 arrangement.jpg
    99.1 KB · Views: 4,780
  • 26 KOA SPR orientation.jpg
    26 KOA SPR orientation.jpg
    153.7 KB · Views: 4,554
  • 27 KOA thermal.jpg
    27 KOA thermal.jpg
    119.2 KB · Views: 4,325
  • 28 lower profile result.jpg
    28 lower profile result.jpg
    281.6 KB · Views: 4,336
Last edited:
Member
Joined 2005
Paid Member
Next part to solder is the led.

Silkscreen it's not clear on led orientation, the silkscren file help us

attachment.php


Sadly the led in BOM doesn't have the dent so we should use leads leght to identify anode and cathode, the right orientation should be this one.

attachment.php


To solder it keep it in place using fingers

attachment.php
 

Attachments

  • 29 led silkscreen.jpg
    29 led silkscreen.jpg
    82.6 KB · Views: 4,271
  • 30 led orientation.jpg
    30 led orientation.jpg
    224.2 KB · Views: 4,285
  • 31 keeping led in place.jpg
    31 keeping led in place.jpg
    163 KB · Views: 4,285
A further note on LED, traces of LED's pads and external LED connectors are parallel so for those that want to use the connector use same orientation.

Let's pass to transitors.

:att'n: there are 2 types of BC639 in BOM: BC639-16 (regulator) and BC639G
(DC-protection)

I choose to start from DC protection ones

When soldering transistors solder one single lead for each

attachment.php


Then solder other leads alternating transistors so to not heat too much parts.

As usual leave thermal pads unsoldered.

attachment.php



attachment.php


attachment.php
 

Attachments

  • 33 solder other leads.jpg
    33 solder other leads.jpg
    159.3 KB · Views: 4,209
  • 32 Soldering first lead of tranny.jpg
    32 Soldering first lead of tranny.jpg
    141.7 KB · Views: 4,269
  • 34 reg trannies.jpg
    34 reg trannies.jpg
    167.1 KB · Views: 4,170
  • 35 transistors soldered.jpg
    35 transistors soldered.jpg
    246.9 KB · Views: 4,238
attachment.php


Note Caddocks MK132 orientation.

attachment.php


Note that R13 can be completely soldered from start even if one lead goes to ground since the bottom pad it's not directly connected to the groundplane.

R104/R204 ground leads are not soldered since on thermals.

attachment.php
 

Attachments

  • 36 R13 orientation.jpg
    36 R13 orientation.jpg
    188.2 KB · Views: 3,022
  • 37 Caddocks soldering.jpg
    37 Caddocks soldering.jpg
    166.7 KB · Views: 3,017
  • 38 Caddocks soldered.jpg
    38 Caddocks soldered.jpg
    217.4 KB · Views: 1,984
As it could be noted all markings on boards are oriented so that marked parts could be easily oriented.

See for FKP2s

attachment.php


FKP2s orientation

attachment.php


attachment.php


Then solder C10

attachment.php
 

Attachments

  • 39 FKP2 orientation.jpg
    39 FKP2 orientation.jpg
    140.5 KB · Views: 1,895
  • 40 filter FKP2.jpg
    40 filter FKP2.jpg
    173.4 KB · Views: 1,846
  • 41 Wima bypasses.jpg
    41 Wima bypasses.jpg
    186.3 KB · Views: 1,917
  • 42 C10.jpg
    42 C10.jpg
    114.3 KB · Views: 1,866
Now it's the turn of connectors.

:att'n: There are two types of Molex included in BOM tin plated (EXT LED) and gold plated (IN)

attachment.php


Then put in place faston tabs and solder on the upper side one end

attachment.php


attachment.php


To obtain this result tabs must be heated with the soldering iron to be soldered

Then reverse board and solder all the tabs:

attachment.php
 

Attachments

  • 43 molex.jpg
    43 molex.jpg
    188.3 KB · Views: 1,830
  • 44 Apply solder.jpg
    44 Apply solder.jpg
    120.6 KB · Views: 1,819
  • 45 result.jpg
    45 result.jpg
    127.5 KB · Views: 1,819
  • 46 solder underside.jpg
    46 solder underside.jpg
    135.1 KB · Views: 1,842
A further note on faston tabs.

If the soldering temperature it's not enough to obtain results depicted in previous post defer their installation to when we'll raise soldering temperature to solder thermal pads.

Back on topic.

Now we solder C1 and C2:

attachment.php


attachment.php


As usual we'll leave thermal pads for later (we'll raise soldering temperature to solder all of them)

It's LM317s turn

attachment.php


Now MP915s

attachment.php


Note that ceramic pads side goes on the outside for both.
 

Attachments

  • 47 C1 and C2.jpg
    47 C1 and C2.jpg
    175.7 KB · Views: 1,815
  • 48 C1 and C2 pads.jpg
    48 C1 and C2 pads.jpg
    130.6 KB · Views: 1,798
  • 49 LM317s.jpg
    49 LM317s.jpg
    192 KB · Views: 1,804
  • 50 MP915s.jpg
    50 MP915s.jpg
    192.9 KB · Views: 1,786
Now an essential component that could be easily forgot resulting in a not working amp or worse...

The unique jumper in the whole board (J1) which carries V-

Using pliers make a 12mm jumper:

attachment.php


If you bought Rikens you can use their gold plated leads after trimming.

attachment.php


attachment.php


Note that J1 jumper is installed in the bottom side and soldered on the upper side.
 

Attachments

  • 51 J1.jpg
    51 J1.jpg
    98.7 KB · Views: 1,770
  • 52 J1 in place.jpg
    52 J1 in place.jpg
    134.7 KB · Views: 1,796
  • 52 j1 pads.jpg
    52 j1 pads.jpg
    190.7 KB · Views: 1,789
Now it's rectifiers diodes turn

attachment.php


attachment.php


As usual thermal pads are left unsoldered.

Proceed soldering the relay, start from one or two pads while keeping it in place with fingers

attachment.php


Proceed with other pads leaving out the thermal one.

attachment.php
 

Attachments

  • 53 MUR820s.jpg
    53 MUR820s.jpg
    186.2 KB · Views: 1,784
  • 54 MUR820s pads.jpg
    54 MUR820s pads.jpg
    126.3 KB · Views: 1,807
  • 55 relay first pad.jpg
    55 relay first pad.jpg
    137.9 KB · Views: 1,775
  • 56 relay pads.jpg
    56 relay pads.jpg
    134.7 KB · Views: 1,977
Prepare R3s with thermal compound (a thin layer)

attachment.php


And fix them to heatsinks using M3 screws and bolts

attachment.php


:att'n: M3 screws and bolts are not indicated in BOM but can be easily sourced from any hardware store. Prefer non magnetic materials like brass.

Solder R3 in place.

Now it's time to raise soldering iron temperature (min 350°C), solder all thermal pads we left in previous steps and trim remaining leads.

attachment.php


Note that in the previous picture I forgot to solder relay's pad...:eek:
 

Attachments

  • 57 R3 compound.jpg
    57 R3 compound.jpg
    94.2 KB · Views: 1,771
  • 58 R3 prepared.jpg
    58 R3 prepared.jpg
    102.2 KB · Views: 1,756
  • 59 soldered thermals.jpg
    59 soldered thermals.jpg
    186.9 KB · Views: 1,768
To solder LM3886TF take measures and drill heatsinks then fix the opamp to heatsinks

attachment.php


Then insert LM3886, together the heatsink, in place on board and solder a pair of pins on the upperside to keep chip in place.

Unmount opamp from heatsink, reverse board and solder all pins.

The nearly ready boards

attachment.php


attachment.php


The only remaining components, not covered here are the big smoothing caps and imput cap.
 

Attachments

  • 60 LM3886 on hs.jpg
    60 LM3886 on hs.jpg
    145.3 KB · Views: 1,776
  • 61 nearly finished board 1.jpg
    61 nearly finished board 1.jpg
    215.4 KB · Views: 1,851
  • 62 nearly finished board 2.jpg
    62 nearly finished board 2.jpg
    211.8 KB · Views: 1,769
3 - Tranformers

As specced each module need a dedicated transformer to avoid hum problems.

Transformers must have double secondaries (2x25V, 2x24 also fine) and 160VA minimum rating (120VA minimum for the more efficient R-Cores).

You must find the label on transformer or its datasheet to wire them.

Selectronic R-Cores

attachment.php


With this type of label the first color in the couple is usually hot/phase, the second neutral.

So:

AC1 Violet
NAC1 Gray
AC2 Blue
NAC2 Red

Antek AN-2225

From manifacturer datasheet:

attachment.php


With this type of label/wiring you can't distiguish visually each secondary from the other.

One way to do it is using a multimeter to measure continuity.

Members of the same couple will have continuity.

After you identified couples wire in this way:

AC1 Green1
NAC1 Blue 1
AC2 Green 2
NAC2 Blue 2
 

Attachments

  • 63 R-core.jpg
    63 R-core.jpg
    104.5 KB · Views: 1,782
  • 64 Antek AN-2225.jpg
    64 Antek AN-2225.jpg
    30 KB · Views: 1,820
Status
This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button.