Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Chip Amps Amplifiers based on integrated circuits

Sallen-key active crossover with as few parts as possible
Sallen-key active crossover with as few parts as possible
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Thread Tools Search this Thread
Old 4th November 2011, 03:59 AM   #1
Circuitsoft is offline Circuitsoft  United States
diyAudio Member
Join Date: May 2007
Send a message via AIM to Circuitsoft Send a message via MSN to Circuitsoft
Default Sallen-key active crossover with as few parts as possible

I'm trying to build an amplifier with active crossover for some car speakers out of a TDA8566Q.

See my most recent attempt is just a highpass with 1nF caps, a 604k feedback, and a 31.6k short from the feedback point to ground. The resistor to ground is the internal load resistance of the amplifier (60K). I'm finding the gain of the amplifier, as a whole, far higher than I expect.

I would link to a JavaCircuitSimulator simulation, but the most recent Java update on my work machine killed copy/paste, and I don't want to type out a 2000 character URL. I'll try again from home.
  Reply With Quote
Old 6th November 2011, 06:43 AM   #2
pacificblue is offline pacificblue  Germany
diyAudio Member
Join Date: May 2008
The TDA8566 is a BTL amp with an internal gain setting of 26 dB. If that is too much for your application, you need an attenuator.

It is also a single supply amp with an internal virtual ground that cannot be accessed from the outside. An additional external feedback loop will not give meaningful results, because it cannot be referenced to that virtual ground. On such a BTL amp you would need two feedback loops anyhow.

From the above you can derive that the TDA8566 is not a candidate to build a Sallen-Key filter around. The filter needs to be completely before the amp and if a passive filter is not good enough for the purpose, you will need additional op amps.
If you've always done it like that, then it's probably wrong. (Henry Ford)
  Reply With Quote


Sallen-key active crossover with as few parts as possibleHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Sallen Key distortion? - simulated vs measured HiFiNutNut Chip Amps 25 21st December 2010 05:05 AM
How to buffer a sallen-key circuit WDYSUN Analog Line Level 7 11th October 2010 09:36 AM
"Sallen-Key" Public domain? mashaffer Tubes / Valves 3 24th July 2008 02:41 AM
is an input buffer needed for a sallen-key filter? oraz Solid State 2 12th May 2008 08:39 PM
Help needed with sourcing active crossover parts Thunau Parts 8 11th April 2003 11:15 PM

New To Site? Need Help?

All times are GMT. The time now is 11:33 AM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.79%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright ©1999-2017 diyAudio