TDA2822 mono input

maurycy · 8th February 2011, 08:14 PM

I have small 1W amplifier based on TDA2822 which I am going to run of 3V and use as a headphone amplifier. Now, the input is going to be from an electric guitar which is mono. What would be the correct way to modify the attached schematic to accept mono source and have the output (mono) but both channels in the headphones?

TDA2822 amp schematic

Thanks

maurycy · 9th February 2011, 12:53 PM

Anyone? Morning crew?

Can I just modify the circuit to use only one channel on the input and then split one channel on the output into two going to headphones?

DigitalJunkie · 9th February 2011, 01:08 PM

I would just join IN1 and IN2 together,and feed your guitar into there. Then you could feed each headphone driver with each channel of the amp.

Are you sure there's enough gain? Guitar output signals are fairly low.

maurycy · 9th February 2011, 01:19 PM

Thanks for replying.

I already have the board with TDA2822 assembled so I can test to see if it has enough gain. If not, I will go with a different chip.

8th February 2011, 08:14 PM	#1
maurycy diyAudio Member Join Date: Dec 2005 Location: NJ	TDA2822 mono input I have small 1W amplifier based on TDA2822 which I am going to run of 3V and use as a headphone amplifier. Now, the input is going to be from an electric guitar which is mono. What would be the correct way to modify the attached schematic to accept mono source and have the output (mono) but both channels in the headphones? TDA2822 amp schematic Thanks

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Stereo to mono input	giralfino	Digital Line Level	3	3rd October 2010 02:27 PM
Mono to stereo input wiring question	Keskin	Class D	8	1st March 2009 11:33 AM
input coupling capacitor VALUE & BRAND for mono LM4780	nickthevoice	Chip Amps	4	13th May 2008 12:57 PM
difference between mixed mono and summed mono	Clipped	Car Audio	4	10th October 2007 11:34 AM
Dual Mono - Anti Mono Power Supplies	pmkap	Everything Else	3	16th February 2002 05:10 AM

New To Site?	Need Help?
Register to Participate Search Privacy Statement Contact Us	Frequently Asked Questions Did you forget your password? Mark Forums Read


	Please consider donating to help us continue to serve you. Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving

9th February 2011, 12:53 PM	#2
maurycy diyAudio Member Join Date: Dec 2005 Location: NJ	Anyone? Morning crew? Can I just modify the circuit to use only one channel on the input and then split one channel on the output into two going to headphones?

9th February 2011, 01:08 PM	#3
DigitalJunkie diyAudio Member Join Date: Apr 2003 Location: Portland,Oregon Blog Entries: 4	I would just join IN1 and IN2 together,and feed your guitar into there. Then you could feed each headphone driver with each channel of the amp. Are you sure there's enough gain? Guitar output signals are fairly low.

9th February 2011, 01:19 PM	#4
maurycy diyAudio Member Join Date: Dec 2005 Location: NJ	Thanks for replying. I already have the board with TDA2822 assembled so I can test to see if it has enough gain. If not, I will go with a different chip.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)