Replacement for STK4192 II

sifuconman · 25th December 2010, 06:42 AM

Hi,

My current amplifier is using STK4192 II but it is damaged now. Can I replace the STK4192 II with a STK4191 II which is available on the market ?

What is the difference between STK4191 II and STK4192 II ?

mjf · 25th December 2010, 02:11 PM

hello.
they seem to be very similar.perhaps the 4191 is only for use with 8 ohm speakers.

STK4192II Datasheet pdf - AF Power Amplifier (Split Power Supply) (50W + 50W min, THD = 0.4%) - SANYO

IndAudio · 28th December 2010, 02:05 PM

Both are pin-to-pin compatible and have very little differences. You can replace a 4192 with a 4191 without any worries.
The only difference is in THD rating which depends on the mark like mark II, V, X etc and minor changes in the internal circuitry and supply voltage leves (4191 -53v against 4192 -52.5).

sifuconman · 3rd March 2011, 10:04 AM

Hi,

Does any one know what should be the normal working voltages on pin no 12 of STK4192 if the supply voltage +vcc is 37 v and -vcc is -37 v ?

The voltage I measured on pin no 12 is almost zero. Is it normal ? If not normal then what could be the problem ?

Thanks

Mooly · 3rd March 2011, 11:25 AM

Just looked at the data sheets for a 4192 and a 4191 and they are certainly not pin compatible.
I am using,
Datasheet catalog for integrated circuits, diodes, triacs, and other semiconductors, view

The 4192 should have a voltage on pin 12 similar to that on pin 11. They may even be joined on the PCB. These are the main supplies to the amp so around 35 to 50 volts depending on what the map runs on,

sifuconman · 3rd March 2011, 02:35 PM

Thanks. I guess my STK 4192 is faulty. Need to change. One more question though - do we need to use an insulator between the heat sink and STK 4192 if the heat sink is grounded ?

Mooly · 3rd March 2011, 05:39 PM

Never seen insulators used on commercial gear. Pin 16 is shown as "ground" so I'm guessing that connects to the metal back plate which may or may not be "grounded".

The IC probably is duff and may have blown circuit protectors (fuses etc) in the PSU, hence no supply on pin 11 etc.

25th December 2010, 06:42 AM	#1
sifuconman diyAudio Member Join Date: Dec 2010	Replacement for STK4192 II Hi, My current amplifier is using STK4192 II but it is damaged now. Can I replace the STK4192 II with a STK4191 II which is available on the market ? What is the difference between STK4191 II and STK4192 II ?

3rd March 2011, 10:04 AM	#4
sifuconman diyAudio Member Join Date: Dec 2010	stk voltage Hi, Does any one know what should be the normal working voltages on pin no 12 of STK4192 if the supply voltage +vcc is 37 v and -vcc is -37 v ? The voltage I measured on pin no 12 is almost zero. Is it normal ? If not normal then what could be the problem ? Thanks

3rd March 2011, 11:25 AM	#5
Mooly diyAudio Member Join Date: Sep 2007	Just looked at the data sheets for a 4192 and a 4191 and they are certainly not pin compatible. I am using, Datasheet catalog for integrated circuits, diodes, triacs, and other semiconductors, view The 4192 should have a voltage on pin 12 similar to that on pin 11. They may even be joined on the PCB. These are the main supplies to the amp so around 35 to 50 volts depending on what the map runs on, __________________ ------------------------------------------------------- *A simulation free zone.* *Design it, build it, test it.*

3rd March 2011, 05:39 PM	#7
Mooly diyAudio Member Join Date: Sep 2007	Never seen insulators used on commercial gear. Pin 16 is shown as "ground" so I'm guessing that connects to the metal back plate which may or may not be "grounded". The IC probably is duff and may have blown circuit protectors (fuses etc) in the PSU, hence no supply on pin 11 etc. __________________ ------------------------------------------------------- *A simulation free zone.* *Design it, build it, test it.*

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search


	Please consider donating to help us continue to serve you. Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving

28th December 2010, 02:05 PM	#3
IndAudio diyAudio Member Join Date: Dec 2010 Location: Bangalore	Both are pin-to-pin compatible and have very little differences. You can replace a 4192 with a 4191 without any worries. The only difference is in THD rating which depends on the mark like mark II, V, X etc and minor changes in the internal circuitry and supply voltage leves (4191 -53v against 4192 -52.5).

3rd March 2011, 02:35 PM	#6
sifuconman diyAudio Member Join Date: Dec 2010	Thanks. I guess my STK 4192 is faulty. Need to change. One more question though - do we need to use an insulator between the heat sink and STK 4192 if the heat sink is grounded ?

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Drive replacement : Westra Xw-165-1394 in Mission 70 MK II ?	ydrol	Multi-Way	2	3rd March 2011 03:48 PM
Quad II - Can 6P3S-E/GU50 be used as KT66 direct replacement?	pwan	Tubes / Valves	7	26th March 2010 07:40 AM
tone arm replacement on gemini XL 500 II	jtwell2	Parts	0	1st August 2008 11:58 PM
Quad II tubes replacement	assimaki	Tubes / Valves	0	28th June 2008 09:10 AM

New To Site?	Need Help?
Register to Participate Search Privacy Statement Contact Us	Frequently Asked Questions Did you forget your password? Mark Forums Read