Need help with chassis layout - diyAudio
Go Back   Home > Forums > Amplifiers > Chip Amps

Chip Amps Amplifiers based on integrated circuits

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 15th December 2008, 09:38 PM   #1
bluegti is offline bluegti  United States
diyAudio Member
 
Join Date: Nov 2004
Location: Northern Virginia
Default Need help with chassis layout

I have the dual mono LM3886 Dual Mono Kit from chipamp.com.

I have two Avel Lindberg (Y236503) transformers from parts express.

I have a chassis that measures roughly 15x15 inches internally.

I'm not sure the best way to layout the chassis. I want to use the existing holes if possible, but will drill new ones on the back if necessary.
  • The RCA inputs are on either side of the back panel.
  • The Speaker binding posts are just offset of center with grounds in the middle
  • The IEC connector is just below the right-hand side RCA Jack
  • The fuse holder is just below the right-hand side binding posts
Please comment on the attached diagram that is very close to scale.
  • The Yellow and Green lines represent how I plan to route the AC input wires.
  • I did not include the wires to connect AC to the transformers, but will most likely use some sort of terminal block.
  • I did not include the secondary wires from the transformers to the power supply board because I think it is pretty obvious.
  • I did not include the wires from the power supply boards to the amplifier boards because I think it is pretty obvious.
  • The purple wires represent the inputs from the RCA jacks to the amplifier boards (I know there will really be two wires).
  • The red and black wires represent the outputs from the amplifier boards to the speaker binding posts.
Does this look like a good layout and routing of wires? Should I be
concerned by the AC running under the channel on the right? Can you suggest a better way or routing the wires? Would I be better off mounting both amplifier boards on the left-hand heat sink and placing the transformers on the right? I could drill a new hole for an RCA jack on the left.

Thanks for your help. This is my first time building a chip amp and first time building any amp solo.
Attached Images
File Type: gif 3886dualmono.gif (15.8 KB, 437 views)
  Reply With Quote
Old 15th December 2008, 10:20 PM   #2
col is offline col  Australia
diyAudio Member
 
col's Avatar
 
Join Date: Feb 2008
Location: Melbourne, Victoria, Australia
Hi Bluegti,

I'm laying out an amp at the moment. It's a pair of Hypex UcD400 with one large 500va Trafo and a pair of power supply boards. Iv'e had it sitting on the bench for days and have been rearranging components a bit like playing chess. I think I nearly have the best configuration.

Usual practise where amp modules is concerned is to separate them as far apart as possible so that you don't get the heat from each module contributing to the other.

With the wiring try to make sure that power, speaker and signal wires are separate and not touching. It's good to use shielded microphone cable on the signal wire if you have any. If not twist them together. I don't think the power cable going under a module will cause any distortion, just don't have it touching. It is also good practise to keep power cables going from the supply to the modules as short as possible.

col.
__________________
http://www.minirig.org.au
  Reply With Quote
Old 21st December 2008, 02:32 AM   #3
diyAudio Member
 
Join Date: Sep 2007
Location: N38
I would keep the AC input wires as far as possible from the RCA input signals, in this case right up the middle. Also, tightly twist the AC input wires and use shielded wire for the RCA input signals.

Richard
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Chassis layout? Psychobiker Tubes / Valves 0 12th March 2008 12:12 PM
Chassis layout help Evenharmonics Tubes / Valves 4 4th March 2008 12:52 AM
Transformer chassis layout Richard Ellis Tubes / Valves 5 27th December 2007 02:54 PM
Chassis Layout & PS questions Valvomaniac Tubes / Valves 3 11th April 2007 08:46 AM
help with chassis layout jarthel Tubes / Valves 5 27th June 2006 05:41 PM


New To Site? Need Help?

All times are GMT. The time now is 12:12 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2