Creative SBS 370 2.1 Speaker Problem

Paswa · 18th November 2007, 04:48 AM

Hey, welcome all friends,,

1 year after buying my Creative SBS 370 2.1 it shows some strange problem. after turning on it, it give crystal clear sound. but after 10-12 second it give a big 'bump' sound and starts humming and the audio output decreased. after 'shaking' the subwoofer box for a few times, it sounds clear again but after 30 seconds the same situation repeat again. Creative serviceman says"It's unrepairable", is it really unrepairable??

ben12345 · 18th November 2007, 09:18 PM

I'd be tempted to pull the board out and check each solder joint to see if any are bad. It it works afted you've shaken it, it sounds like this is the most likely problem.

WEALSPEAKER · 19th November 2007, 01:41 AM

well try to heat the ic by using hair dryer if you see some changeds happen when ic is heated change it some ics do fail after a while of work your problem is really very possible caused by ic fail when its heat increase

i do have question people do any one know what the replacement of yd1006 ic it is 18watt audio amplifier if any one knows please tell me

Paswa · 19th November 2007, 02:01 AM

thanks for your answers. I heated the ic by a hair-dryer, but no
changes happen.

And his question, TDA2030 can be used as a substitite of YD1006

WEALSPEAKER · 19th November 2007, 07:39 AM

FRIEND PAWSA YOU HAVE THEN TO REPLACE THE ELECTROLIC AND CERAMIC CAP NEAR THE IC THIS IS ONLY THING THAT REMAINS ?ALSO YOU HVAE TO HEAT THE IC VERY WELL SO YOU CAN OBSERVE WHAT BAD CHANGES THAT HAPPEN IF NOTHING HAPPEN THEN WAGE YOUR WAR AGAINST CAPS CHANGE THEM ALL ......SO REALLY TDA2030 =YD1006 SO I CAN REPLACE THEM IN YOUR RESPONSIBILITY??

Paswa · 19th November 2007, 11:53 AM

why duplicate thread. see it at TDA 1006 datasheet

pravardhan · 28th September 2010, 04:38 PM

@Paswa

1st of all how is your speaker now?

2nd can you post more photos of SBS 370 opened?

3rd what is the size (inches) of the Woofer used in the Sub-Woofer?

joemadiy · 14th October 2010, 08:35 PM

Hey Anybody help to to fix my Speaker problem of SBS 370,which is left speaker output is not working, both speakers is in working good condition . i checked it with plugged in righthand side output. can any body help me to fix this probelm.

rakesh_sharma23 · 15th October 2010, 07:43 AM

Try to change the input signal cable. Second check for any burned or lose solder component.

If this not solve the issue then the IC is gone. Change the IC with new one.

hew128 · 17th December 2011, 12:21 AM

Hi Paswa,

I started searching the forum after my unit experience similar issues e.g powers up but no sound. Did you manage to find a replacement for the IC?

Thanks!

18th November 2007, 04:48 AM	#1
Paswa diyAudio Member Join Date: Aug 2007	Creative SBS 370 2.1 Speaker Problem Hey, welcome all friends,, 1 year after buying my Creative SBS 370 2.1 it shows some strange problem. after turning on it, it give crystal clear sound. but after 10-12 second it give a big 'bump' sound and starts humming and the audio output decreased. after 'shaking' the subwoofer box for a few times, it sounds clear again but after 30 seconds the same situation repeat again. Creative serviceman says"It's unrepairable", is it really unrepairable??

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Speaker problem	nandax	Multi-Way	4	10th December 2008 08:33 AM
Problem in creative I-trigue 3400 speaker system	chtan82	Multi-Way	1	15th April 2008 01:12 PM
Most creative speaker enclosure?	mashaffer	Multi-Way	27	15th March 2006 02:07 AM
MLS measurement with Speaker Workshop and Creative USB sound card: not working	tcpip	Multi-Way	35	22nd August 2005 03:22 AM
speaker problem	Xplorer	Car Audio	1	9th June 2004 10:29 AM

New To Site?	Need Help?
Register to Participate Search Privacy Statement Contact Us	Frequently Asked Questions Did you forget your password? Mark Forums Read


	Please consider donating to help us continue to serve you. Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving

18th November 2007, 09:18 PM	#2
ben12345 diyAudio Member Join Date: Feb 2006 Location: UK	I'd be tempted to pull the board out and check each solder joint to see if any are bad. It it works afted you've shaken it, it sounds like this is the most likely problem.

19th November 2007, 01:41 AM	#3
WEALSPEAKER diyAudio Member Join Date: Nov 2007	well try to heat the ic by using hair dryer if you see some changeds happen when ic is heated change it some ics do fail after a while of work your problem is really very possible caused by ic fail when its heat increase i do have question people do any one know what the replacement of yd1006 ic it is 18watt audio amplifier if any one knows please tell me

19th November 2007, 02:01 AM	#4
Paswa diyAudio Member Join Date: Aug 2007	thanks for your answers. I heated the ic by a hair-dryer, but no changes happen. And his question, TDA2030 can be used as a substitite of YD1006

19th November 2007, 07:39 AM	#5
WEALSPEAKER diyAudio Member Join Date: Nov 2007	FRIEND PAWSA YOU HAVE THEN TO REPLACE THE ELECTROLIC AND CERAMIC CAP NEAR THE IC THIS IS ONLY THING THAT REMAINS ?ALSO YOU HVAE TO HEAT THE IC VERY WELL SO YOU CAN OBSERVE WHAT BAD CHANGES THAT HAPPEN IF NOTHING HAPPEN THEN WAGE YOUR WAR AGAINST CAPS CHANGE THEM ALL ......SO REALLY TDA2030 =YD1006 SO I CAN REPLACE THEM IN YOUR RESPONSIBILITY??

19th November 2007, 11:53 AM	#6
Paswa diyAudio Member Join Date: Aug 2007	why duplicate thread. see it at TDA 1006 datasheet

28th September 2010, 04:38 PM	#7
pravardhan diyAudio Member Join Date: Aug 2010 Location: Bangalore, Karnataka, India	@Paswa 1st of all how is your speaker now? 2nd can you post more photos of SBS 370 opened? 3rd what is the size (inches) of the Woofer used in the Sub-Woofer?

14th October 2010, 08:35 PM	#8
joemadiy diyAudio Member Join Date: Oct 2010	Hey Anybody help to to fix my Speaker problem of SBS 370,which is left speaker output is not working, both speakers is in working good condition . i checked it with plugged in righthand side output. can any body help me to fix this probelm.

15th October 2010, 07:43 AM	#9
rakesh_sharma23 diyAudio Member Join Date: Apr 2005 Location: India	Try to change the input signal cable. Second check for any burned or lose solder component. If this not solve the issue then the IC is gone. Change the IC with new one.

17th December 2011, 12:21 AM	#10
hew128 diyAudio Member Join Date: Jan 2006 Location: Singapore	Hi Paswa, I started searching the forum after my unit experience similar issues e.g powers up but no sound. Did you manage to find a replacement for the IC? Thanks!

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)