Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Chip Amps Amplifiers based on integrated circuits

Can this set up increase the output power of LM1875 at 4 ohms??
Can this set up increase the output power of LM1875 at 4 ohms??
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 17th November 2007, 01:01 AM   #1
Leolabs is offline Leolabs  Malaysia
diyAudio Member
 
Leolabs's Avatar
 
Join Date: Dec 2004
Location: Bukit Mertajam
Send a message via MSN to Leolabs
Default Can this set up increase the output power of LM1875 at 4 ohms??

A single LM1875 will produce 20W into 8/4 ohms at +/-20V.Wonder if add a pair of current booster,will the output power at 4 ohms be increase to,let say 40W at 4 ohms at +/-20V???

Below is an example circuit:
Attached Images
File Type: gif 060708125065371.gif (14.0 KB, 538 views)
  Reply With Quote
Old 17th November 2007, 08:36 AM   #2
consort_ee_um is offline consort_ee_um  United Kingdom
diyAudio Member
 
Join Date: May 2004
Location: Hertfordshire
This circuit is very close to the datasheet recommended booster circuit for the similar TDA2030. I have used the booster with both types of devices. You do not need R6 and R7 (can be replaced with short circuit)
  Reply With Quote
Old 17th November 2007, 08:57 AM   #3
richie00boy is offline richie00boy  United Kingdom
Did it Himself
diyAudio Member
 
richie00boy's Avatar
 
Join Date: Nov 2003
Location: Gloucestershire, England, UK
Can this set up increase the output power of LM1875 at 4 ohms??
The limiting factor is the supply voltage which is dictated by the chip. All you can do by adding booster transistors is run the chip at its max voltage, which it is probably only rated at 8 ohms for. So you will see a small gain in power but not huge.
__________________
www.readresearch.co.uk my website for UK diy audio people - designs, PCBs, modules and more.
  Reply With Quote
Old 17th November 2007, 09:42 AM   #4
Paswa is offline Paswa  India
diyAudio Member
 
Paswa's Avatar
 
Join Date: Aug 2007
the main reason 4 using the chip, because it creates very low distortion. If u use the booster transistor, the output'll be more distorted than the single chip...
  Reply With Quote
Old 17th November 2007, 10:02 AM   #5
Anthony C Smith is offline Anthony C Smith  United Kingdom
diyAudio Member
 
Join Date: Jun 2005
Location: Sunderland
this circuit is good for 35w RMS into 4r at low thd- cannot comment on the layout; when I have used this topology I always put the 1875 in the middle;looks better and lays out with shorter paths
I use 1R5 base resistors and a 220n cap across the 1875 rails and no 0.2r tail resistors; you will also need an input capacitor across the 47k Rin to prevent emi RFI suseptability (I use 22k not 47k and 470pF)
otherwise this is a good device use.
In a former life I used a version of this bridged to deliver 100W into 1R from a single 22V rail for voice alarm with no problems other than heat.
__________________
Anthony C Smith MAES MinstSCE
-I think rain is wet so who am I to Judge-
  Reply With Quote
Old 17th November 2007, 02:24 PM   #6
Leolabs is offline Leolabs  Malaysia
diyAudio Member
 
Leolabs's Avatar
 
Join Date: Dec 2004
Location: Bukit Mertajam
Send a message via MSN to Leolabs
Can smaller power BJT such as TIP41/TIP42 be used???
  Reply With Quote
Old 17th November 2007, 05:55 PM   #7
Juergen Knoop is offline Juergen Knoop  Germany
diyAudio Member
 
Juergen Knoop's Avatar
 
Join Date: Jan 2007
use at least the 'a' version. The basic TIP41 has a too low voltage rating.
My boosted TDA2030 utilises BD711/712 which are slightly more powerful than the TIPs (Pt 75W instead 65W).
Regards
  Reply With Quote
Old 25th November 2007, 11:29 AM   #8
Anthony C Smith is offline Anthony C Smith  United Kingdom
diyAudio Member
 
Join Date: Jun 2005
Location: Sunderland
I have always used BD911 & BD912 as the ST ones are cheap and have 15A Ic Limit.
regards
__________________
Anthony C Smith MAES MinstSCE
-I think rain is wet so who am I to Judge-
  Reply With Quote

Reply


Can this set up increase the output power of LM1875 at 4 ohms??Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
LM4702:increase the output current,possible?? Leolabs Chip Amps 3 14th January 2008 04:11 PM
Increase the output swing of LM3875,possible??? Leolabs Chip Amps 8 20th August 2007 02:50 AM
Can An Output Transformer Change A Voltage Amp's Output Impedance From 0.1 To 47 Ohms kelticwizard Everything Else 11 25th March 2007 05:17 AM
how to increase output power on a 400watt amp db junkie Solid State 14 11th October 2005 07:20 AM
ESP 3A output power at 4 ohms load Freddie Solid State 19 5th January 2004 06:02 PM


New To Site? Need Help?

All times are GMT. The time now is 01:09 AM.


Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.79%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Copyright ©1999-2018 diyAudio
Wiki